hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
1.47k
| content
stringlengths 0
6.67M
|
|---|---|---|---|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.1.2 Minimum requirements
|
The accuracy requirement in table 8.7.11.1.1 is valid under the following conditions:
P-CCPCH_RSCP1,2 -102 dBm..
where the received P-CCPCH Ec/Io is defined as,
and the received SCH Ec/Io is defined as,
and SCH_Ec/Ior is equally divided between primary synchronisation code and the sum of all secondary synchronisation codes, where the secondary synchronisation codes are also equally divided.
Table 8.7.11.1.1: SFN-CFN observed time difference accuracy for an intra frequency UTRA TDD neighbour cell
Parameter
Unit
Accuracy [chip]
Conditions
Io [dBm/3,84 MHz]
SFN-CFN observed time difference
chip
+/-0,5
-94...-50
The normative reference for this requirement is TS 25.123 [2] clause 9.1.1.11 and A.9.1.10.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.1.3 Test Purpose
|
The purpose of this test is to verify that the measurement accuracy of SFN-CFN observed time difference is within the limit specified in clause 8.7.11.1.2.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.1.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.1.4.1 Initial conditions
|
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
In this case all cells are on the same frequency. Cell 1 and cell 2 shall be synchronised, i.e. share the same frame and timeslot timing. The DL DPCH shall be transmitted in timeslot 4 and the UL DPCH shall be transmitted in timeslot 12. The second Beacon timeslot shall be provided in timeslot 8 for cell 1 and in timeslot 10 for cell 2. During the test, the timing difference between cell 1 and cell 2 can be set to any value from 0…255 frames. The SFN-CFN observed time difference accuracy requirements in the intra-frequency case are tested by using test parameters in Table 8.7.11.1.2.
Table 8.7.11.1.2: SFN-CFN observed time difference intra frequency test parameters
Parameter
Unit
Test 1
Test 2
Test 3
Cell 1
Cell 2
Cell 1
Cell 2
Cell 1
Cell 2
DL timeslot number
0
2
0
2
0
2
UTRA RF Channel number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
SCH_toffset
0
5
0
5
0
5
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
Ioc
dBm / 3,84 MHz
-75.2
-75.2
-57.8
-54.7
-98.7
-98.7
Îor/Ioc
dB
5
5
7
3
3
3
Io, Note 1
dBm / 3,84 MHz
-69
-50
-94
Propagation condition
AWGN
AWGN
AWGN
NOTE 1: Io levels have been calculated from other parameters for information purposes. They are not settable parameters themselves.
1) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.2.3. The RF parameters for Test 1 are set up according to table 8.7.11.1.2.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.1.4.2 Procedure
|
1) SS shall transmit the MEASUREMENT CONTROL message.
2) UE shall transmit periodically MEASUREMENT REPORT messages.
3) SS shall check "OFF" and "Tm" values in MEASUREMENT REPORT message and calculate SFN-CFN observed time difference value according to the definition in clause 5.1.11 of TS 25.225 [22]. This value shall be compared to the actually set SFN-CFN observed time difference value for each MEASUREMENT REPORT message.
4) SS shall count the number of MEASUREMENT REPORT messages transmitted by UE. After 1000 MEASUREMENT REPORT messages have been received from UE, the RF parameters are set up according to table 8.7.11.1.2 for Test 2. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 1s and ignore the MEASUREMENT REPORT messages during this period. Then, steps 2) and 3) above are repeated. After further 1000 MEASUREMENT REPORT messages have been received from UE, the RF parameters are set up according to table 8.7.11.1.2 for Test 3. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 1s and ignore the MEASUREMENT REPORT messages during this period. Then, steps 2) and 3) above are repeated.
5) After further 1000 MEASUREMENT REPORT messages have been received from UE, the SS shall transmit RRC CONNECTION RELEASE message.
6) UE shall transmit RRC CONNECTION RELEASE COMPLETE message.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] and in Annex I, with the following exceptions:
MEASUREMENT CONTROL message (Step 1):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Periodical reporting
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH RSCP
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
Virtual/active set cells + 2
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria (10.3.7.
-Periodical reporting criteria (10.3.7.53)
-Amount of reporting
Infinity
-Reporting interval
250 ms
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.1.5 Test requirements
|
The SFN-CFN observed time difference accuracy shall meet the requirements in clause 8.7.11.1.2.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.7.11.1A Intra frequency measurement requirement for 1,28 Mcps option
Void
8.7.11.1B Intra frequency measurement requirement for 7,68 Mcps option
8.7.11.1B.1 Definition and applicability
The intra frequency SFN-CFN observed time difference is defined as the SFN-CFN observed time difference from the active cell to a neighbour cell that is in the same frequency. This measurement is specified in clause 5.1.11 of TS 25.225 [22]. The reference point for the SFN-CFN observed time difference shall be the antenna connector of the UE.
The requirements and this test apply to all types of UTRA TDD UE.
8.7.11.1B.2 Minimum requirements
The accuracy requirement in table 8.7.11.1B.2.1 is valid under the following conditions:
P-CCPCH_RSCP1,2 -102 dBm..
where the received P-CCPCH Ec/Io is defined as,
and the received SCH Ec/Io is defined as,
and SCH_Ec/Ior is equally divided between primary synchronisation code and the sum of all secondary synchronisation codes, where the secondary synchronisation codes are also equally divided.
Table 8.7.11.1B.2.1: SFN-CFN observed time difference accuracy for an intra frequency UTRA TDD neighbour cell
Parameter
Unit
Accuracy [chip]
Conditions
Io [dBm/7.68 MHz]
SFN-CFN observed time difference
chip
+/-1
-94...-50
The normative reference for this requirement is TS 25.123 [2] clause 9.1.1.11.1 and A.9.3.10.
8.7.11.1B.3 Test Purpose
The purpose of this test is to verify that the measurement accuracy of SFN-CFN observed time difference is within the limit specified in clause 8.7.11.1B.2.
8.7.11.1B.4 Method of test
8.7.11.1B.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
In this case all cells are on the same frequency. Cell 1 and cell 2 shall be synchronised, i.e. share the same frame and timeslot timing. The DL DPCH shall be transmitted in timeslot 4 and the UL DPCH shall be transmitted in timeslot 12. The second Beacon timeslot shall be provided in timeslot 8 for cell 1 and in timeslot 10 for cell 2. During the test, the timing difference between cell 1 and cell 2 can be set to any value from 0…255 frames. The SFN-CFN observed time difference accuracy requirements in the intra-frequency case are tested by using test parameters in Table 8.7.11.1B.4.1.1.
Table 8.7.11.1B.4.1.1: SFN-CFN observed time difference intra frequency test parameters
Parameter
Unit
Test 1
Test 2
Test 3
Cell 1
Cell 2
Cell 1
Cell 2
Cell 1
Cell 2
DL timeslot number
0
2
0
2
0
2
UTRA RF Channel number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
SCH_toffset
0
5
0
5
0
5
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
Ioc
dBm / 7.68 MHz
-75.2
-75.2
-57.8
-54.7
-98.7
-98.7
Îor/Ioc
dB
5
5
7
3
3
3
Io, Note 1
dBm / 7.68 MHz
-69
-50
-94
Propagation condition
AWGN
AWGN
AWGN
NOTE 1: Io levels have been calculated from other parameters for information purposes. They are not settable parameters themselves.
1) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.2.3. The RF parameters for Test 1 are set up according to table 8.7.11.1B.4.1.1.
8.7.11.1B.4.2 Procedure
1) SS shall transmit the MEASUREMENT CONTROL message.
2) UE shall transmit periodically MEASUREMENT REPORT messages.
3) SS shall check "OFF" and "Tm" values in MEASUREMENT REPORT message and calculate SFN-CFN observed time difference value according to the definition in clause 5.1.11 of TS 25.225 [22]. This value shall be compared to the actually set SFN-CFN observed time difference value for each MEASUREMENT REPORT message.
4) SS shall count the number of MEASUREMENT REPORT messages transmitted by UE. After 1000 MEASUREMENT REPORT messages have been received from UE, the RF parameters are set up according to table 8.7.11.1B.4.1.1 for Test 2. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 1s and ignore the MEASUREMENT REPORT messages during this period. Then, steps 2) and 3) above are repeated. After further 1000 MEASUREMENT REPORT messages have been received from UE, the RF parameters are set up according to table 8.7.11.1B.4.1.1 for Test 3. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 1s and ignore the MEASUREMENT REPORT messages during this period. Then, steps 2) and 3) above are repeated.
5) After further 1000 MEASUREMENT REPORT messages have been received from UE, the SS shall transmit RRC CONNECTION RELEASE message.
6) UE shall transmit RRC CONNECTION RELEASE COMPLETE message.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] and in Annex I, with the following exceptions:
MEASUREMENT CONTROL message (Step 1):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Periodical reporting
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH RSCP
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
Virtual/active set cells + 2
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria (10.3.7.
-Periodical reporting criteria (10.3.7.53)
-Amount of reporting
Infinity
-Reporting interval
250 ms
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
8.7.11.1B.5 Test requirements
The SFN-CFN observed time difference accuracy shall meet the requirements in clause 8.7.11.1B.2.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.2 Inter frequency measurement requirement for 3,84 Mcps option
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.2.1 Definition and applicability
|
The inter frequency SFN-CFN observed time difference is defined as the SFN-CFN time difference from the active cell to a UTRA TDD neighbour cell that is in a different frequency. This measurement is specified in clause 5.1.11 of TS 25.225 [22]. The reference point for the SFN-CFN observed time difference shall be the antenna connector of the UE.
The requirements and this test apply to all types of UTRA TDD UE.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.2.2 Minimum requirements
|
The accuracy requirement in table 8.7.11.2.1 is valid under the following conditions:
P-CCPCH_RSCP1,2 -102 dBm..
where the received P-CCPCH Ec/Io is defined as,
and the received SCH Ec/Io is defined as,
and SCH_Ec/Ior is equally divided between primary synchronisation code and the sum of all secondary synchronisation codes, where the secondary synchronisation codes are also equally divided.
Table 8.7.11.2.1: SFN-CFN observed time difference accuracy for an inter frequency UTRA TDD neighbour cell
Parameter
Unit
Accuracy [chip]
Conditions
Io [dBm/3,84 MHz]
SFN-CFN observed time difference
chip
+/-0,5
-94...-50
The normative reference for this requirement is TS 25.123 [2] clause 9.1.1.11 and A.9.1.10.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.2.3 Test purpose
|
The purpose of this test is to verify that the measurement accuracy of SFN-CFN observed time difference is within the limit specified in clause 8.7.11.2.2.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.2.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.2.4.1 Initial conditions
|
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
In this case, UTRA TDD cell 1 and UTRA TDD cell 2 are on different frequencies. Cell 1 and cell 2 shall be synchronised, i.e. share the same frame and timeslot timing. The DL DPCH shall be transmitted in timeslot 4 and the UL DPCH shall be transmitted in timeslot 12. The second Beacon timeslot shall be provided in timeslot 8 for cell 1 and in timeslot 10 for cell 2. During the test, the timing difference between cell 1 and cell 2 can be set to any value from 0…256 frames. The SFN-CFN observed time difference accuracy requirements in the intra-frequency case are tested by using test parameters in Table 8.7.11.2.2.
Table 8.7.11.2.2: SFN-CFN observed time difference inter frequency test parameters
Parameter
Unit
Test 1
Test 2
Test 3
Cell 1
Cell 2
Cell 1
Cell 2
Cell 1
Cell 2
DL timeslot number
0
2
0
2
0
2
UTRA RF Channel number
Channel 1
Channel 2
Channel 1
Channel 2
Channel 1
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
SCH_toffset
0
5
0
5
0
5
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
Ioc
dBm / 3,84 MHz
-75.2
-75.2
-57.8
-54.7
-98.7
-98.7
Îor/Ioc
dB
5
5
7
3
3
3
Io, Note 1
dBm / 3,84 MHz
-69
-50
-94
Propagation condition
AWGN
AWGN
AWGN
NOTE 1: Io levels have been calculated from other parameters for information purposes. They are not settable parameters themselves.
1) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.2.3. The RF parameters for Test 1 are set up according to table 8.7.11.2.2.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.2.4.2 Procedure
|
1) SS shall transmit the MEASUREMENT CONTROL message.
2) UE shall transmit periodically MEASUREMENT REPORT messages.
3) SS shall check "OFF" and "Tm" values in MEASUREMENT REPORT message and calculate SFN-CFN observed time difference value according to the definition in clause 5.1.11 of TS 25.225 [22]. This value shall be compared to the actually set SFN-CFN observed time difference value for each MEASUREMENT REPORT message.
4) SS shall count the number of MEASUREMENT REPORT messages transmitted by UE. After 1000 MEASUREMENT REPORT messages have been received from UE, the RF parameters are set up according to table 8.7.11.2.2 for Test 2. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 1s and ignore the MEASUREMENT REPORT messages during this period. Then, steps 2) and 3) above are repeated. After further 1000 MEASUREMENT REPORT messages have been received from UE, the RF parameters are set up according to table 8.7.11.2.2 for Test 3. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 1s and ignore the MEASUREMENT REPORT messages during this period. Then, steps 2) and 3) above are repeated.
5) After further 1000 MEASUREMENT REPORT messages have been received from UE, the SS shall transmit RRC CONNECTION RELEASE message.
6) UE shall transmit RRC CONNECTION RELEASE COMPLETE message.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] and in Annex I, with the following exceptions:
MEASUREMENT CONTROL message for inter frequency measurements (Step 1):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
2
-Measurement Command (10.3.7.46)
Setup
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Periodical reporting
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
-CHOICE inter-frequency cell removal
Not present
-New inter-frequency cells
Cell 2 information is included
-Cell for measurement
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting critera
Inter-frequency reporting criteria
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA carrier RSSI
FALSE
-Frequency quality estimate
TRUE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE
-Cell identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN Reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
Virtual/active set cells + 2
-Measurement validity (10.3.7.51)
Not present
-Inter-frequency set update
Not present
-CHOICE report criteria (10.3.7.
-Periodical reporting criteria (10.3.7.53)
-Amount of reporting
Infinity
-Reporting interval
500 ms
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.11.2.5 Test requirements
|
The SFN-CFN observed time difference accuracy shall meet the requirements in clause 8.7.11.2.2.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.7.11.2A Inter frequency measurement requirement for 1,28 Mcps option
Void
8.7.11.2B Inter frequency measurement requirement for 7,68 Mcps option
8.7.11.2B.1 Definition and applicability
The inter frequency SFN-CFN observed time difference is defined as the SFN-CFN time difference from the active cell to a UTRA TDD neighbour cell that is in a different frequency. This measurement is specified in clause 5.1.11 of TS 25.225 [22]. The reference point for the SFN-CFN observed time difference shall be the antenna connector of the UE.
The requirements and this test apply to 7.68Mcps TDD UE.
8.7.11.2B.2 Minimum requirements
The accuracy requirement in table 8.7.11.2B.2.1 is valid under the following conditions:
P-CCPCH_RSCP1,2 -102 dBm..
where the received P-CCPCH Ec/Io is defined as,
and the received SCH Ec/Io is defined as,
and SCH_Ec/Ior is equally divided between primary synchronisation code and the sum of all secondary synchronisation codes, where the secondary synchronisation codes are also equally divided.
Table 8.7.11.2B.2.1: SFN-CFN observed time difference accuracy for an inter frequency UTRA TDD neighbour cell
Parameter
Unit
Accuracy [chip]
Conditions
Io [dBm/7.68 MHz]
SFN-CFN observed time difference
chip
+/-1
-94...-50
The normative reference for this requirement is TS 25.123 [2] clause 9.1.1.11.1 and A.9.3.10.
8.7.11.2B.3 Test purpose
The purpose of this test is to verify that the measurement accuracy of SFN-CFN observed time difference is within the limit specified in clause 8.7.11.2B.2.
8.7.11.2B.4 Method of test
8.7.11.2B.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
In this case, UTRA TDD cell 1 and UTRA TDD cell 2 are on different frequencies. Cell 1 and cell 2 shall be synchronised, i.e. share the same frame and timeslot timing. The DL DPCH shall be transmitted in timeslot 4 and the UL DPCH shall be transmitted in timeslot 12. The second Beacon timeslot shall be provided in timeslot 8 for cell 1 and in timeslot 10 for cell 2. During the test, the timing difference between cell 1 and cell 2 can be set to any value from 0…256 frames. The SFN-CFN observed time difference accuracy requirements in the intra-frequency case are tested by using test parameters in Table 8.7.11.2B.4.1.1.
Table 8.7.11.2B.4.1.1: SFN-CFN observed time difference inter frequency test parameters
Parameter
Unit
Test 1
Test 2
Test 3
Cell 1
Cell 2
Cell 1
Cell 2
Cell 1
Cell 2
DL timeslot number
0
2
0
2
0
2
UTRA RF Channel number
Channel 1
Channel 2
Channel 1
Channel 2
Channel 1
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
SCH_toffset
0
5
0
5
0
5
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
Ioc
dBm / 7.68 MHz
-75.2
-75.2
-57.8
-54.7
-98.7
-98.7
Îor/Ioc
dB
5
5
7
3
3
3
Io, Note 1
dBm / 7.68 MHz
-69
-50
-94
Propagation condition
AWGN
AWGN
AWGN
NOTE 1: Io levels have been calculated from other parameters for information purposes. They are not settable parameters themselves.
1) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.2.3. The RF parameters for Test 1 are set up according to table 8.7.11.2B.4.1.1.
8.7.11.2.4B.2 Procedure
1) SS shall transmit the MEASUREMENT CONTROL message.
2) UE shall transmit periodically MEASUREMENT REPORT messages.
3) SS shall check "OFF" and "Tm" values in MEASUREMENT REPORT message and calculate SFN-CFN observed time difference value according to the definition in clause 5.1.11 of TS 25.225 [22]. This value shall be compared to the actually set SFN-CFN observed time difference value for each MEASUREMENT REPORT message.
4) SS shall count the number of MEASUREMENT REPORT messages transmitted by UE. After 1000 MEASUREMENT REPORT messages have been received from UE, the RF parameters are set up according to table 8.7.11.2B.4.1.1 for Test 2. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 1s and ignore the MEASUREMENT REPORT messages during this period. Then, steps 2) and 3) above are repeated. After further 1000 MEASUREMENT REPORT messages have been received from UE, the RF parameters are set up according to table 8.7.11.2B.4.1.1 for Test 3. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 1s and ignore the MEASUREMENT REPORT messages during this period. Then, steps 2) and 3) above are repeated.
5) After further 1000 MEASUREMENT REPORT messages have been received from UE, the SS shall transmit RRC CONNECTION RELEASE message.
6) UE shall transmit RRC CONNECTION RELEASE COMPLETE message.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] and in Annex I, with the following exceptions:
MEASUREMENT CONTROL message for inter frequency measurements (Step 1):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
2
-Measurement Command (10.3.7.46)
Setup
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Periodical reporting
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
-CHOICE inter-frequency cell removal
Not present
-New inter-frequency cells
Cell 2 information is included
-Cell for measurement
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting critera
Inter-frequency reporting criteria
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA carrier RSSI
FALSE
-Frequency quality estimate
TRUE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE
-Cell identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN Reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
Virtual/active set cells + 2
-Measurement validity (10.3.7.51)
Not present
-Inter-frequency set update
Not present
-CHOICE report criteria (10.3.7.
-Periodical reporting criteria (10.3.7.53)
-Amount of reporting
Infinity
-Reporting interval
500 ms
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
8.7.11.2B.5 Test requirements
The SFN-CFN observed time difference accuracy shall meet the requirements in clause 8.7.11.2B.2.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.12 UE transmitted power
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.12.1 UE transmitted power for 3.84 Mcps TDD Option
|
Void
8.7.12.1A UE transmitted power for 1.28 Mcps TDD Option
8.7.12.1A.1 Definition and applicability
The UE transmitted power absolute accuracy is defined as difference between the UE reported value and the UE transmitted power measured by test system. The reference point for the UE transmitted power shall be the antenna connector of the UE.
The requirements and this test apply to all types of 1.28 Mcps TDD UE.
8.7.12.1A.2 Minimum requirements
The measurement period in CELL_DCH state and CELL_FACH state is 1 slot.
Table 8.7.12.1A.2.1 UE transmitted power absolute accuracy
Parameter
Unit
Accuracy [dB]
PUEMAX
24dBm
PUEMAX
21dBm
UE transmitted power PUEMAX
dBm
+1/-3
2
PUEMAX > UE transmitted power PUEMAX-1
dBm
+1,5/-3,5
2,5
PUEMAX-1 > UE transmitted power PUEMAX-2
dBm
+2/-4
3
PUEMAX-2 > UE transmitted power PUEMAX-3
dBm
+2,5/-4,5
3,5
PUEMAX-3 > UE transmitted power PUEMAX-10
dBm
+3/-5
4
NOTE 1: User equipment maximum output power, PUEMAX, is the maximum output power level without tolerance defined for the power class of the UE in 3GPP TS 25.102 "UTRA (UE) TDD; Radio Transmission and Reception".
NOTE 2: UE transmitted power is the reported value.
The normative reference for this requirement is TS 25.123 clause 9.1.2.1.
8.7.12.1A.3 Test purpose
The purpose of this test is to verify that for any reported value of UE Transmitted Power in the range PUEMAX to PUEMAX-10 that the actual UE mean power lies within the range specified in clause 8.7.12.1A.2.
8.7.12.1A.4 Method of test
8.7.12.1A.4.1 Initial conditions
Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS to the UE antenna connector as shown in figure A.1.
The test parameters are given in Table 8.7.12.1A.4.1 and 8.7.12.1A.4.2 below. In the measurement control information it shall be indicated to the UE that periodic reporting of the UE transmitted power measurement shall be used.
Table 8.7.12.1A.4.1: General test parameters for UE transmitted power
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in clause C.3.1.2
DL-Power Control
Off
Table 8.7.12.1A.4.2: Cell Specific parameters for UE transmitted power
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
UTRA RF Channel Number (NOTE 2)
Channel 1
PCCPCH_Ec/Ior
dB
-3
D wPCH _Ec/Ior
dB
0
OCNS_Ec/Ior
dB
- 3
dB
3
dBm/1.28 MHz
-70
PCCPCH_RSCP
(NOTE 1)
dBm
-70
Propagation Condition
AWGN
NOTE 1: PCCPCH RSCP level has been calculated from other parameters for information purposes. They are not settable parameters themselves.
NOTE2: In the case of multi-frequency network, the UTRA RF Channel Number can be set for the primary frequency in this test.
8.7.12.1A.4.2 Procedure
1) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.2. The RF parameters are set up according to table 8.7.12.1A.4.1 and 8.7.12.1A.4.2. Set the UE power and Maximum allowed UL TX power to the maximum power for the UE power class.
2) SS shall send continuously during the entire test Up power control commands to the UE.
3) SS shall transmit the MEASUREMENT CONTROL message as defined in the specific message contents below.
4) Decode the UE Transmitted power reported by the UE in the next available MEASUREMENT REPORT message.
5) Measure the mean power of the UE over a period of one timeslot.
6) Steps 4 and 5 shall be repeated until statistical significance according to Annex F.6.2.8 is achieved.
7) Decrease the Maximum allowed UL TX power by 1 dB. The SS shall transmit the PHYSICAL CHANNEL RECONFIGURATION message, as defined in the specific message contents below.
8) SS shall wait for the PHYSICAL CHANNEL RECONFIGURATION COMPLETE message from the UE.
9) Repeat from step 4) until the Maximum allowed UL TX Power reaches PUEMAX-10.
Specific Message Contents
All messages indicated above shall use the same content as described in default message content in clause 9 of 34.108 [3], with the following exceptions:
MEASUREMENT CONTROL message:
Information Element
Value/Remark
Message Type
UE information elements
-RRC transaction identifier
-Integrity check info
-message authentication code
-RRC message sequence number
0
SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
SS provides the value of this IE, from its internal counter.
Measurement Information elements
-Measurement Identity
-Measurement Command
-CHOICE Measurement type
-UE Internal measurement quantity
-Measurement quantity
-Filter coefficient
-UE Internal reporting quantity
-UE Transmitted power
-CHOICE mode
-CHOICE TDD option
-1.28Mcps TDD
-Tadv info
-CHOICE report criteria
-Amount of reporting
-Reporting interval
-Measurement Reporting Mode
-Measurement Report Transfer Mode
-Periodical Reporting / Event Trigger Reporting Mode
-AdditionalMeasurementList
5
SETUP
UE Internal measurement
UE Transmitted power
0
TRUE
TDD
False
Periodical reporting criteria
Infinity
250
AM RLC
Periodical reporting
Not Present
MEASUREMENT REPORT message:
Information Element
Value/remark
Message Type
Integrity check info
The presence of this IE is dependent on PIXIT statements in TS 34.123-2. If integrity protection is indicated to be active, this IE shall be present with the values of the sub IEs as stated below. Else, this IE and the sub-IEs shall be absent.
- Message authentication code
This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS.
- RRC Message sequence number
This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Measurement identity
5
Measured Results
- CHOICE Measurement
UE Internal measured results
- Choice mode
TDD
- UE Transmitted power list
Checked that this IE is present
-UE Transmitted power
Checked that this IE is present
- CHOICE TDD option
-1.28Mcps TDD
-Tadv
Checked that this IE is absent
Measured results on RACH
Checked that this IE is absent
Additional measured results
Checked that this IE is absent
Event results
Checked that this IE is absent
PHYSICAL CHANNEL RECONFIGURATION message:
Information Element
Value/Remark
Version
Message Type
UE Information Elements
-RRC transaction identifier
-Integrity check info
-message authentication code
-RRC message sequence number
-Integrity protection mode info
-Ciphering mode info
-Activation time
-New U-RNTI
-New C-RNTI
-RRC State Indicator
-UTRAN DRX cycle length coefficient
0
SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
SS provides the value of this IE, from its internal counter.
Not Present
Not Present
Not Present
Not Present
Not Present
CELL_DCH
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
PhyCH information elements
-Frequency info
Not Present
Uplink radio resources
-Maximum allowed UL TX power
At the first time this value is set to PUEMAX-1. After the second time this value is decreased with 1 dB from previous value.
8.7.12.1A.5 Test requirements
Compare each of the UE transmitted power reports against the following mean power measurement. At least 90% of the mean power measurements for any one value of reported UE transmitted power shall be within the range specified in table 8.7.12.1A.5.
Table 8.7.12.1A.5 UE transmitted power test requirements
UE reported value
SS measured mean power (X) range [dBm]
PUEMAX
24dBm
PUEMAX
21dBm
UE_TX_POWER_104
33-3.7 X < 34+1.7
33-2.7 X < 34+2.7
UE_TX_POWER_103
32-3.7 X < 33+1.7
32-2.7 X < 33+2.7
UE_TX_POWER_097
26-3.7 X < 27+1.7
UE_TX_POWER_096
25-3.7 X < 26+1.7
UE_TX_POWER_095
24-3.7 X < 25+1.7
UE_TX_POWER_094
23-4.2 X < 24+2.2
23-2.7 X < 24+2.7
UE_TX_POWER_093
22-4.7 X < 23+2.7
22-2.7 X < 23+2.7
UE_TX_POWER_092
21-5.2 X < 22+3.2
21-2.7 X < 22+2.7
UE_TX_POWER_091
20-5.7 X < 21+3.7
20-3.2 X < 21+3.2
UE_TX_POWER_090
19-5.7 X < 20+3.7
19-3.7 X < 20+3.7
UE_TX_POWER_089
18-5.7 X < 19+3.7
18-4.2 X < 19+4.2
UE_TX_POWER_088
17-4.7 X < 18+4.7
UE_TX_POWER_087
16-4.7 X < 17+4.7
UE_TX_POWER_086
15-4.7 X < 15+4.7
UE_TX_POWER_022
-49-5.7 X < -48+3.7
-49-4.7 X < -48+4.7
UE_TX_POWER_021
-50-5.7 X < -49+3.7
-50-4.7 X < -49+4.7
NOTE 1: Although test requirements are given for all UE reported values, a good UE will likely report values between PUEMAX and PUEMAX - 10 dB. However, even a good UE may report also wider range of values due to errors in TPC command reception and allowed range specified for UE transmit power setting accuracy when Maximum Allowed UL TX Power has been signaled. On the other hand, a faulty UE may report any power value but then it does not fulfill the Table 8.7.12.1A.5 requirements for mean power or then it will not pass some other tests e.g. TC 5.2 of this specification.
NOTE 2: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.13 UE Transmission Power Headroom
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.13.1 UPH for 3.84Mcps TDD Option
|
Void
8.7.13.1A UPH for 1.28Mcps TDD Option
8.7.13.1A.1 Definition and applicability
The accuracy requirements for the UE transmission power headroom depends on the total power transmitted by the UE as defined in the functionality in section 9.2.6.3 of TS 25.321[14], section 9.1.2.3.2 of TS 25.123 [2] and section 5.1.16 of TS 25.225 [22]. The requirements and this test apply to Release 7 and later releases for all types of UTRA for the 1.28Mcps TDD UE that supports E-DCH and HSDPA.
8.7.13.1A.2 Minimum Requirements
The UE transmission power headroom (UPH) is defined in section 5.1.16 of TS 25.225 [22] as the ratio of the maximum UE transmission power and the product of P e-base power and serving cell path loss, and shall be calculated as following:
Where:
P max, tx = min {Maximum allowed UL TX Power, P max} is the UE maximum transmission power;
Maximum allowed UL TX Power is set by UTRAN and defined in [9];
P max is the UE nominal maximum output power according to the UE power class and specified in [1] table 6.1;
P e-base is a closed-loop quantity defined in [9] and L Path_loss is the serving cell path loss.
The reference point for the UE transmission power headroom shall be the antenna connector of the UE.
The accuracy requirements for UE transmission power headroom depends on the total power transmitted by the UE. Table 8.7.13.1A defines the accuracy of the measured quantity as defined in section 9.1.2.3.2 of TS 25.123 [2].
Table 8.7.13.1A.1: UPH reporting accuracy
Total UE output power value (dBm)
UPH reporting Accuracy [dB]*
PUEMAX 24dBm
PUEMAX 21dBm
Total output power PUEMAX
+1/-3
2
PUEMAX-1 Total output power <PUEMAX
+1,5/-3,5
2,5
PUEMAX-2 Total output power <PUEMAX-1
+2/-4
3
PUEMAX-3 Total output power <PUEMAX-2
+2,5/-4,5
3,5
PUEMAX-10 Total output power <PUEMAX-3
+3/-5
4
*Note: UPH reporting accuracy is the difference between the UPH reported by the UE and the actual uplink power headroom
**Note: PUEMAX, is the maximum output power level without tolerance defined for the power class of the UE in 3GPP TS 25.102
8.7.13.1A.3 Test purpose
The purpose of this test case is to verify that the UE transmission power headroom measurement report accuracy is within the specified limits defined in section 9.1.2.3.2 of 25.123 [2] shown in table 8.7.13.1A.1.
8.7.13.1A.4 Method of test
8.7.13.1A.4.1 Initial conditions
Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS (node B emulator) to the UE antenna connector as shown in figure A.1.
2) HSDPA and E-DCH configurations are set as in table 8.7.13.1A.2.
Table 8.7.13.1A.2: General test parameters for UE transmission power headroom
Parameter
Unit
Value
Comment
DL DCH configuration
DL Reference Measurement Channel 12.2 kbps
As specified in Annex C.3.1.2 of the present document
DL configuration
DL Fixed Reference Channel (FRC 1)
As specified in Annex C.4.2.1 of the present document
E-DCH configuration
5 ms TTI E-DCH Transport Block Size Table 0 according to TS 25.321 [13] annex BC.1
DL Power Control
Off
Active cell
Cell 1
Reference E-TFCI index
0 as per Table 0 according to TS 25.321 [13] annex BC.1.
3) The power levels and cell specific parameters are set as in table 8.7.13.1A.3.
Table 8.7.13.1A.3: Cell Specific parameters for UE transmission power headroom
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
UTRA RF Channel Number (NOTE 2)
Channel 1
PCCPCH_Ec/Ior
dB
- 3
D wPCH _Ec/Ior
dB
0
OCNS_Ec/Ior
dB
- 3
dB
3
dBm/ 1.28 MHz
-70
PCCPCH RSCP,
Note 1
dB m
-70
Propagation Condition
AWGN
NOTE 1: PCCPCH RSCP level has been calculated from other parameters for information purposes. They are not settable parameters themselves.
NOTE2: In the case of multi-frequency network, the UTRA RF Channel Number can be set for the primary frequency in this test.
4) The UE is switched on.
5) An E-DCH call is set up according to TS 34.108 [3] 7.3.9 with the following exceptions in the RADIO BEARER SETUP message. These e exceptions are derived from Table 8.7.13.2, and in addition allow the beta values to be set and each UL physical channel to be at constant power during the measurement.
Table 8.7.13.1A.4: Contents of RADIO BEARER SETUP message: AM or UM (E-DCH and HSDPA)
Information Element/Group name
Value/Remark
E-PUCH Info(TDD only)
>E-TFCS information
>>Reference Beta Information QPSK list
>>>Reference Code Rate
0.2
>>>Reference Beta
-14
>>Reference Beta Information QPSK list
>>>Reference Code Rate
0.3
>>>Reference Beta
-13
>>Reference Beta Information QPSK list
>>>Reference Code Rate
0.4
>>>Reference Beta
-12
>>Reference Beta Information QPSK list
>>>Reference Code Rate
0.5
>>>Reference Beta
-10
>>Reference Beta Information QPSK list
>>>Reference Code Rate
0.6
>>>Reference Beta
-9
>>Reference Beta Information QPSK list
>>>Reference Code Rate
0.7
>>>Reference Beta
-8
>>Reference Beta Information QPSK list
>>>Reference Code Rate
0.8
>>>Reference Beta
-7
>>Reference Beta Information QPSK list
>>>Reference Code Rate
0.9
>>>Reference Beta
-6
>>Reference Beta Information 16QAM list
>>>Reference Code Rate
0.2
>>>Reference Beta
-9
>>Reference Beta Information 16QAM list
>>>Reference Code Rate
0.3
>>>Reference Beta
-8
>>Reference Beta Information 16QAM list
>>>Reference Code Rate
0.4
>>>Reference Beta
-6
>>Reference Beta Information 16QAM list
>>>Reference Code Rate
0.5
>>>Reference Beta
-5
>>Reference Beta Information 16QAM list
>>>Reference Code Rate
0.6
>>>Reference Beta
-4
>>Reference Beta Information 16QAM list
>>>Reference Code Rate
0.7
>>>Reference Beta
-2
>>Reference Beta Information 16QAM list
>>>Reference Code Rate
0.8
>>>Reference Beta
-1
>>Reference Beta Information 16QAM list
>>>Reference Code Rate
0.9
>>>Reference Beta
0
>CHOICE TDD mode
>>1.28 Mcps TDD
>>>PRXdes_base
-85
>>>Beacon PL Est.
>>>TPC step size
1
>>>E-PUCH TS configuration list
>>>>TS number
1
>>>E-PUCH TS configuration list
>>>>TS number
2
>>>Minimum allowed code rate
3(0.1)
>>>Maximum allowed code rate
50(0.8)
8.7.13.1A.4.2 Test procedure
1) The Scheduling Information configuration for the E-DCH indicates to the UE that it shall periodically report Scheduling Information, which contains UPH measurement every E-DCH TTI. During the test the system simulator shall not send any scheduling grant to the UE, and therefore the UE will not send any payload data on the E-DCH.
2) The SS shall set the CPRI value in E-AGCH to be 3 dB for a power class 3 UE, or 0 dB for a power class 4 UE by using uplink power control. CRRI and TRRI value in E-AGCH respectively is “00100”and “11000”.
3) The SS measures both the power transmitted by the UE on E-PUCH and the total output power of the UE in time slot which assigned E-PUCH transmitted by SS. The SS shall analyse the E-TFCI transmitted on the E-UCCH for each E-DCH TTI and estimates the e. The SS averages both the E-PUCH output power，e and total output power of the UE over 100 times. Then, the SS calculates the difference between average E-PUCH power measured and e.
4) The SS estimates the UE transmission power headroom as the difference between the maximum allowed uplink transmits power (P max) and the difference calculated in step 3.
5) The SS notes the UE transmission power headroom value reported in the Scheduling Information.
6) The SS calculates the difference between the UE transmission power headroom value estimated in step 4 and the reported UE transmission power headroom noted in step 5. The SS notes this as the UE transmission power headroom accuracy, and compares it to the applicable limit according to the total output power measured in step 3.
7) If the UE transmission power headroom accuracy exceeds the value in Table 8.7.13.1A.5 count a bad result, otherwise a good result with respect to the actually set TX power.
8) Repeat steps 3 to 7 in order to collect more good or bad results for the currently set power level. Continue the repetition, until statistical significance according to Annex F.6.2.8 is achieved.
9) The SS sends 5 up TPC commands at the nesting E-AGCH to bring the TX power of the UE up by a nominal 1 dB step, and then alternate UP/DOWN to maintain constant TX power.
10) Repeat steps 3 through 9 and note the UE transmission power headroom accuracy for each UE total power value until the UE stops reporting UPH or does not give lower UPH values for 8 consecutive repetitions of steps 3 through 9.
8.7.13.1A.5 Test requirements
The UE transmission power headroom measurement report accuracy recorded in steps 6, 9 and 10 above shall meet the requirements in table 8.7.13.1A.5. The rate of correct measurements observed during repeated tests shall be at least 90%. To pass the test, the UE transmission power headroom accuracy for each power level in the reporting range must pass. Once a power level is passed, no more results need be collected on this power level.
Table 8.7.13.1A.5: Test requirement for UPH reporting accuracy
Total UE output power value (dBm)
UPH reporting Accuracy [dB]*
PUEMAX 24dBm
PUEMAX 21dBm
Total output power PUEMAX
+1.7/-3.7
2.7
PUEMAX-1 Total output power <PUEMAX
+2.2/-4.2
3.2
PUEMAX-2 Total output power <PUEMAX-1
+2.7/-4.7
3.7
PUEMAX-3 Total output power <PUEMAX-2
+3.2/-5.2
4.2
PUEMAX-10 Total output power <PUEMAX-3
+3.7/-5.7
4.7
*Note: UPH reporting accuracy is the difference between the UPH reported by the UE and the actual uplink power headroom
**Note: PUEMAX, is the maximum output power level without tolerance defined for the power class of the UE in 3GPP TS 25.102
NOTE1: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.7.13.1B UPH for 7.68Mcps TDD Option
Void
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.14 E-UTRAN FDD RSRP
|
Editor’s note: This Test case is incomplete for frequencies above 3GHz
• The Test system uncertainties applicable above 3GHz are undefined
• The Test Tolerances and Test Requirements applicable above 3GHz are undefined
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.14.1 Definition and applicability
|
The absolute accuracy of RSRP is defined as the RSRP measured from a cell that has different carrier frequency from the serving cell.
The E-UTRAN FDD RSRP absolute accuracy measurement is used for handover between UTRAN TDD and E-UTRAN FDD for Rel.9 and later.
The requirements and this test apply to the combined UTRAN TDD and E-UTRAN FDD UE.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.14.2 Minimum Requirements
|
In Cell DCH state, whether or not UE requires idle intervals to perform E-UTRAN measurements, the requirements for accuracy of E-UTRA RSRP measurements in CELL_DCH state shall be the same as the inter-frequency RSRP Accuracy Requirements in 3GPP TS 36.133, as follows:
Cell specific reference signals are transmitted either from one, two or four antenna ports.
Conditions defined in 36.101 Section 7.3 for reference sensitivity are fulfilled.
RSRP|dBm according to 36.133 Annex B.3.3 for a corresponding Band
Table 8.7.14.2-1: RSRP Inter frequency absolute accuracy
Parameter
Unit
Accuracy [dB]
Conditions1
Normal condition
Extreme condition
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23, 24, 33, 34, 35, 36, 37, 38, 39, 40
Bands 2, 5, 7, 41
Band 25
Bands 3, 8, 12, 13, 14, 17, 20, 22
Bands 9, 42, 43
Io
Io
Io
Io
Io
RSRP for Ês/Iot -6 dB
dBm
6
9
-121dBm/15kHz … -70dBm/ BWChannel
-119dBm/15kHz … -70dBm/ BWChannel
-117.5dBm/15kHz … -70dBm/ BWChannel
-118dBm/15kHz … -70dBm/ BWChannel
-120dBm/15kHz … -70dBm/ BWChannel
RSRP for Ês/Iot -6 dB
dBm
8
11
-70dBm/ BWChannel … -50dBm/ BWChannel
-70dBm/ BWChannel … -50dBm/ BWChannel
-70dBm/ BWChannel … -50dBm/ BWChannel
-70dBm/ BWChannel … -50dBm/ BWChannel
-70dBm/ BWChannel … -50dBm/ BWChannel
Note 1: Io is assumed to have constant EPRE across the bandwidth.
The normative reference for this requirement is TS 25.123 [2] clauses 9.1.1.5a and A.9.2.5a.1.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.14.3 Test purpose
|
The purpose of this test is to verify that the E-UTRA FDD RSRP measurement absolute accuracy is within the specified limits. This test will verify the requirements in 8.7.14.2 and applies to UE supporting this capability.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.14.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.14.4.1 Initial conditions
|
Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see clauses G.2.1 and G.2.2.
Frequencies to be tested: see table J.2 in Annex J.
In the test in Cell_DCH state, “E-UTRAN FDD RSRP Measurement” is applied to measure on E-UTRAN FDD.
Tables 8.7.14.4.1-1 and 8.7.14.4.1-2 define the limits of signal strengths and code powers on the UTRA TDD cell. In the measurement control information periodic reporting of E-UTRAN FDD RSRP is indicated to the UE. The E-UTRAN FDD test parameters are given in Table 8.7.14.4.1-3.
Table 8.7.14.4.1-1: General parameters of E-UTRA FDD RSRP measurement tests
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Active cell
Cell 1
1.28Mcps TDD cell
Neighbour cell
Cell 2
E-UTRA FDD cell
CP length of cell 2
normal
Idle intervals period
ms
80
As specified in TS 25.331
Filter coefficient
0
L3 filtering is not used
Inter-RAT(E-UTRA FDD) measurement quantity
E-UTRA FDD RSRP
Table 8.7.14.4.1-2: E-UTRA FDD RSRP measurement tests parameters (cell 1)
Parameter
Unit
Test 1, Test 2
DL timeslot number
0
DwPTS
UTRA RF Channel number (NOTE)
Channel 1
PCCPCH_Ec/Ior
dB
-3
DwPCH_Ec/Ior
dB
0
OCNS_Ec/Ior
dB
-3
Îor/Ioc
dB
3
Ioc
dBm / 1.28MHz
-75
Propagation condition
AWGN
NOTE: In the case of multi-frequency, the UTRA RF Channel Number can be set for the primary frequency in this test.
Table 8.7.14.4.1-3: E-UTRA FDD RSRP measurement tests parameters (cell 2)
Parameter
Unit
Test 1
Test 2
E-UTRA RF Channel Number
1
1
BWchannel
MHz
10
10
Measurement bandwidth
22—27
22—27
PDCCH/PCFICH/PHICH Reference measurement channel defined in A.2.1 in TS 36.521-3 [33]
R.6 FDD
R.6 FDD
OCNG Patterns defined in D.1.2 (OP.2 FDD) in TS 36.521-3 [33]
OP.2 FDD
OP.2 FDD
PBCH_RA
dB
0
0
PBCH_RB
PSS_RA
SSS_RA
PCFICH_RB
PHICH_RA
PHICH_RB
PDCCH_RA
PDCCH_RB
PDSCH_RA
PDSCH_RB
OCNG_RANote1
OCNG_RBNote1
Note2
Bands 1, 4, 6,10, 11, 18, 19, 21, 23 and 24
dBm/15 kHz
-88.65
-117
Bands 2, 5 and 7
-115
Band 25
-113.5
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-114
Band 9
-116
dB
10
-4
RSRPNote3
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dBm/15 kHz
-78.65
-121
Bands 2, 5 and 7
-119
Band 25
-117.5
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-118
Band 9
-120
IoNote3
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dBm/9 MHz
-50.45
-87.76
Bands 2, 5 and 7
-85.76
Band 25
-84.26
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-84.76
Band 9
-86.76
dB
10
-4
Propagation condition
-
AWGN
AWGN
Note 1: OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled.
Note 3: RSRP and Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves.
Note 4: RSRP minimum requirements are specified assuming independent interference and noise at each receiver antenna port.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.14.4.2 Test Procedure
|
1) A call is set up according to the test procedure specified in TS 34.108 [3] clause 7.3.2. The RF parameters for Test 1 are set up according to table 8.7.14.5-2.
2) SS shall transmit the MEASUREMENT CONTROL message for inter RAT measurement. In the measurement control information periodic reporting of the EUTRAN FDD RSRP is requested to the UE.
3) UE shall transmit periodically MEASUREMENT REPORT messages.
4) SS shall check RSRP value of Cell 2 in the MEASUREMENT REPORT messages. Levels of Cell 2 reported by the UE are compared to the actual level of Cell 2 for each MEASUREMENT REPORT message.
5) SS shall check MEASUREMENT REPORT messages transmitted by UE until statistical significance according to Annex Tables G.2.3-1 in TS 36.521-3 [33] is achieved.
6) The RF parameters are set up according to tables 8.7.14.5-3 for Test 2. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 5s and ignore the MEASUREMENT REPORT messages during this period. Then, step 4) and 5) above are repeated.
7) The SS shall transmit RRC CONNECTION RELEASE message.
8) UE shall transmit RRC CONNECTION RELEASE COMPLETE message.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3], with the following exceptions:
NOTE: Numbers in brackets after an item e.g “Message Type (10.2.17)” in the IE description are references to clause numbers in TS 25.331 [9] describing that item in more detail.
MEASUREMENT CONTROL message for EUTRAN FDD measurement (Step 1):
Information Element
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
-Integrity check info
0
Not Present
Measurement Information elements
-Measurement Identity
-Measurement Command
-Measurement Reporting Mode
- Measurement Report Transfer Mode
- Periodical Reporting / Event Trigger Reporting Mode
-Additional measurement list
-CHOICE Measurement Type
-Inter-frequency measurement object list
-CHOICE Inter-frequency cell removal
-New inter-frequency cells
-Cell for measurement
-Inter-frequency measurement quantity
-CHOICE reporting criteria
-Filter coefficient
-CHOICE mode
-Measurement quantity
-Inter-frequency reporting quantity
-UTRA Carrier RSSI
-Frequency quality estimate
-Non frequency related cell reporting quantities
-SFN-SFN observed time difference reporting indicator
-Cell synchronisation information reporting indicator
-Maximum number of reported cells
-Measurement validity
-Inter-frequency set update
-CHOICE report criteria
-Amount of reporting
-Reporting interval
2
Setup
Acknowledged mode RLC
Periodical reporting
Not Present
Inter-RAT measurement
Not Present
Cell 2 information is included
Not Present
Inter-frequency reporting criteria
0
EUTRAN FDD
RSRP
FALSE
FALSE
No report
Report all active set cells + cells within monitored set on used frequency
Virtual/active set cells + 1
Not Present
Not Present
Periodical reporting criteria
Infinity
500 ms
Physical channel information elements
-DPCH compressed mode status info
Not Present
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.14.5 Test requirements
|
Table 8.7.14.5-2 and table 8.7.14.5-3 defines the primary level settings including test tolerances for all tests.
For the test to pass, the ratio of successful reported values according to table 8.7.14.5-4 in each test shall be more than 90%, with a confidence level of 95%.
Table 8.7.14.5-1: Void
Table 8.7.14.5-2: UTRAN TDD cell specific test parameters for E-UTRAN FDD RSRP absolute accuracy tests
Parameter
Unit
Test 1, Test 2
DL timeslot number
0
DwPTS
UTRA RF Channel number (NOTE)
Channel 1
PCCPCH_Ec/Ior
dB
-3
DwPCH_Ec/Ior
dB
0
OCNS_Ec/Ior
dB
-3
Îor/Ioc
dB
3
Ioc
dBm / 1.28MHz
-75
Propagation condition
AWGN
NOTE: In the case of multi-frequency, the UTRA RF Channel Number can be set for the primary frequency in this test.
Table 8.7.14.5-3: E-UTRAN FDD cell specific test parameters for E-UTRAN FDD RSRP absolute accuracy tests
Parameter
Unit
Test 1
Test 2
E-UTRA RF Channel Number
1
1
BWchannel
MHz
10
10
Measurement bandwidth
22—27
22—27
PDCCH/PCFICH/PHICH Reference measurement channel defined in A.2.1 in TS 36.521-3 [33]
R.6 FDD
R.6 FDD
OCNG Patterns defined in D.1.2 (OP.2 FDD) in TS 36.521-3 [33]
OP.2 FDD
OP.2 FDD
PBCH_RA
dB
0
0
PBCH_RB
PSS_RA
SSS_RA
PCFICH_RB
PHICH_RA
PHICH_RB
PDCCH_RA
PDCCH_RB
PDSCH_RA
PDSCH_RB
OCNG_RANote1
OCNG_RBNote1
Note2
Bands 1, 4, 6,10, 11, 18, 19, 21, 23 and 24
dBm/15 kHz
-88.95
-117.00
Bands 2, 5 and 7
-115.00
Band 25
-113.50
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-114.00
Band 9
-116.00
dB
10.00
-3.20
RSRPNote3
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dBm/15 kHz
-78.95
-120.20
Bands 2, 5 and 7
-118.20
Band 25
-116.70
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-117.20
Band 9
-119.20
IoNote3
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dBm/9 MHz
-50.75
-87.52
Bands 2, 5 and 7
-85. 52
Band 25
-84.02
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-84.52
Band 9
-86.52
dB
10.00
-3.20
Propagation condition
-
AWGN
AWGN
Note 1: OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled.
Note 3: RSRP and Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves.
Note 4: RSRP minimum requirements are specified assuming independent interference and noise at each receiver antenna port.
Table 8.7.14.5-4: E-UTRAN FDD RSRP absolute accuracy requirements for the reported values
Test 1
Test 2
All bands
Bands 1, 4, 6, 10, 11 18, 19, 21, 23, 24
Bands 2, 5, 7
Band 25
Bands 3, 8, 12, 13, 14, 17, 20, 22
Band 9
Normal Conditions
Lowest reported value (Cell 2)
RSRP_52
RSRP_13
RSRP_15
RSRP_17
RSRP_16
RSRP_14
Highest reported value (Cell 2)
RSRP_71
RSRP_28
RSRP_30
RSRP_31
RSRP_31
RSRP_29
Extreme Conditions
Lowest reported value (Cell 2)
RSRP_49
RSRP_10
RSRP_12
RSRP_14
RSRP_13
RSRP_11
Highest reported value (Cell 2)
RSRP_74
RSRP_31
RSRP_33
RSRP_34
RSRP_34
RSRP_32
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.15 E-UTRAN TDD RSRP
|
Editor’s note: This Test case is incomplete for frequencies above 3GHz
• The Test system uncertainties applicable above 3GHz are undefined
• The Test Tolerances and Test Requirements applicable above 3GHz are undefined
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.15.1 Definition and applicability
|
The absolute accuracy of RSRP is defined as the RSRP measured from a cell that has different carrier frequency from the serving cell.
The E-UTRAN TDD RSRP absolute accuracy measurement is used for handover between UTRAN TDD and E-UTRAN TDD.
The requirements and this test apply to release 9 and later releases UTRA 1.28Mcps TDD UEs that support release 8 and later releases E-UTRA TDD.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.15.2 Minimum Requirements
|
In Cell DCH state, whether or not UE requires idle intervals to perform E-UTRAN measurements, the requirements for accuracy of E-UTRA RSRP measurements in CELL_DCH state shall be the same as the inter-frequency RSRP Accuracy Requirements in 3GPP TS 36.133 [26], as follows:
Cell specific reference signals are transmitted either from one, two or four antenna ports.
Conditions defined in TS 36.101 [27] Section 7.3 for reference sensitivity are fulfilled.
RSRP|dBm according to TS 36.133 [26] Annex B.3.3 for a corresponding Band
Table 8.7.15.2-1: RSRP Inter frequency absolute accuracy
Parameter
Unit
Accuracy [dB]
Conditions1
Normal condition
Extreme condition
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23, 24, 33, 34, 35, 36, 37, 38, 39, 40
Bands 2, 5, 7, 41
Band 25
Bands 3, 8, 12, 13, 14, 17, 20, 22
Bands 9, 42, 43
Io
Io
Io
Io
Io
RSRP for Ês/Iot -6 dB
dBm
6
9
-121dBm/15kHz … -70dBm/ BWChannel
-119dBm/15kHz … -70dBm/ BWChannel
-117.5dBm/15kHz … -70dBm/ BWChannel
-118dBm/15kHz … -70dBm/ BWChannel
-120dBm/15kHz … -70dBm/ BWChannel
RSRP for Ês/Iot -6 dB
dBm
8
11
-70dBm/ BWChannel … -50dBm/ BWChannel
-70dBm/ BWChannel … -50dBm/ BWChannel
-70dBm/ BWChannel … -50dBm/ BWChannel
-70dBm/ BWChannel … -50dBm/ BWChannel
-70dBm/ BWChannel … -50dBm/ BWChannel
Note 1: Io is assumed to have constant EPRE across the bandwidth.
The normative reference for this requirement is TS 25.123 [2] clauses 9.1.1.5a and A.9.2.5a.2.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.15.3 Test purpose
|
The purpose of this test is to verify that the E-UTRA TDD RSRP measurement absolute accuracy is within the specified limits. This test will verify the requirements in 8.7.15.2 and applies to UE supporting this capability.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.15.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.15.4.1 Initial conditions
|
Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see clauses G.2.1 and G.2.2.
Frequencies to be tested: see table J.2 in Annex J.
In the test in Cell_DCH state, “E-UTRAN TDD RSRP Measurement” is applied to measure on E-UTRAN TDD.
Tables 8.7.15.4.1-1 and 8.7.15.4.1-2 define the limits of signal strengths and code powers on the UTRA TDD cell. In the measurement control information periodic reporting of E-UTRAN TDD RSRP is indicated to the UE. The E-UTRAN TDD test parameters are given in Table 8.7.15.4.1-3.
Table 8.7.15.4.1-1: General parameters of E-UTRA TDD RSRP measurement tests
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in section C.3.1
Power Control
On
Target quality value on DTCH
BLER
0.01
Active cell
Cell 1
1.28Mcps UTRA TDD cell
Neighbour cell
Cell 2
E-UTRA TDD cell
CP length of cell 2
Normal
Uplink-downlink configuration of cell 2
1
As specified in table 4.2.2 in TS 36.211 [30]
Special subframe configuration of cell 2
6
As specified in table 4.2.1 in TS 36.211 [30]
Idle intervals period
ms
80
As specified in TS 25.331 [9]
Filter coefficient
0
L3 filtering is not used
Inter-RAT(E-UTRA TDD) measurement quantity
E-UTRA TDD RSRP
Table 8.7.15.4.1-2: E-UTRA TDD RSRP measurement tests parameters (cell 1)
Parameter
Unit
Test 1, Test 2
DL timeslot number
0
DwPTS
UTRA RF Channel number Note2
Channel 1
PCCPCH_Ec/Ior
dB
-3
DwPCH_Ec/Ior
dB
0
OCNS_Ec/Ior
dB
-3
Ioc
dBm/1.28MHz
-75
Îor/Ioc
dB
3
PCCPCH RSCP Note1
dBm
-75
Io Note 1
dBm/1.28MHz
-70.24
Propagation condition
AWGN
NOTE 1: PCCPCH RSCP and Io levels have been calculated from other parameters for information purposes. They are not settable parameters themselves.
NOTE 2: In the case of multi-frequency network of 1.28 Mcps TDD, the UTRA RF Channel Number can be set for the primary frequency in this test.
Table 8.7.15.4.1-3: E-UTRA TDD RSRP measurement tests parameters (cell 2)
Parameter
Unit
Test 1
Test 2
E-UTRA RF Channel Number
2
2
BWchannel
MHz
10
10
Measurement bandwidth
22—27
22—27
PDCCH/PCFICH/PHICH Reference measurement channel defined in A.2.2 in TS 36.521-3 [33]
R.6 TDD
R.6 TDD
OCNG Patterns defined in D2.2 (OP.2 TDD) in TS 36.521-3 [33]
OP.2 TDD
OP.2 TDD
PBCH_RA
dB
0
0
PBCH_RB
PSS_RA
SSS_RA
PCFICH_RB
PHICH_RA
PHICH_RB
PDCCH_RA
PDCCH_RB
PDSCH_RA
PDSCH_RB
OCNG_RANote1
OCNG_RBNote1
Note2
Bands 33 ~ 40
dBm/15 kHz
-88.65
-117
Bands 42 and 43
-116
Band 41
-115
dB
10
-4
RSRPNote3
Bands 33 ~ 40
dBm/15 kHz
-78.65
-121
Bands 42 and 43
-120
Band 41
-119
IoNote3
Bands 33 ~ 40
dBm/9 MHz
-50.45
-87.76
Bands 42 and 43
-86.76
Band 41
-85.76
dB
10
-4
Propagation condition
-
AWGN
AWGN
Note 1: OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled.
Note 3: RSRP and Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves.
Note 4: RSRP minimum requirements are specified assuming independent interference and noise at each receiver antenna port.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.15.4.2 Test Procedure
|
1) A call is set up according to the test procedure specified in TS 34.108 [3] clause 7.3.2. The RF parameters for Test 1 are set up according to tables 8.7.15.5-2 and 8.7.15.5-3.
2) SS shall transmit the MEASUREMENT CONTROL message for inter RAT measurement. In the measurement control information periodic reporting of the EUTRAN TDD RSRP is requested to the UE.
3) After sending the measurement control message, wait for 10s, then the UE shall transmit periodically MEASUREMENT REPORT messages.
4) After the 10s wait in step 3), SS shall check E-UTRAN TDD RSRP value of Cell 2 in periodical MEASUREMENT REPORT messages. E-UTRAN TDD RSRP power of Cell 2 reported by UE is compared to actual E-UTRAN TDD RSRP value of Cell 2 for each MEASUREMENT REPORT message. If the UE fails to report the measurement values including neighbour cell RSRP, the number of failures is increased by one.
5) SS shall check MEASUREMENT REPORT messages transmitted by UE until statistical significance according to Annex Tables G.2.3-1 in TS 36.521-3 [33] is achieved.
6) The RF parameters are set up according to table s 8.7.15.5-2 and 8.7.15. 5-3 for Test 2. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 5s and ignore the MEASUREMENT REPORT messages during this period. Then, step 3) to 5) above are repeated.
7) The SS shall transmit RRC CONNECTION RELEASE message.
8) UE shall transmit RRC CONNECTION RELEASE COMPLETE message.
Specific Message Contents
All messages indicated above shall use the same content as described in default message content in clause 9 of TS 34.108 [3], and clause 4.4 and 4.7B.1 of TS 36.508 [28] with the following exceptions:
MEASUREMENT CONTROL message for EUTRAN TDD measurement (Step 2):
Derivation Path: TS 36.508 [28], clause 4.7B.1 Table 4.7B.1-3: MEASUREMENT CONTROL
Information Element
Value/remark
Comment
Condition
Message Type
RRC transaction identifier
0
Measurement Identity
2
Measurement Reporting Mode
- Measurement Report Transfer Mode
Acknowledged mode RLC
- CHOICE Inter-RAT measurement objects
E-UTRA frequency list
- New frequencies
- E-UTRA carrier frequency
Downlink EARFCN of E-UTRA Cell
- Measurement bandwidth
mbw6
- Periodical Reporting/Event Trigger Reporting Mode
Periodical reporting
CHOICE Measurement type
Inter-RAT measurement
- Inter-RAT measurement quantity
- Measurement quantity for UTRAN quality estimate
- Filter coefficient
0
- CHOICE mode
TDD
TDD_UTRA
- Measurement quantity
Primary CCPCH RSCP
- CHOICE system
E-UTRA
- Measurement quantity
RSRP
- Filter coefficient
0
- CHOICE report criteria
Periodical reporting criteria
- Periodical reporting criteria
- Amount of reporting
Infinity
- Reporting interval
500 ms
- Reporting cell status
- CHOICE reported cell
Report cells within active set or within virtual active set or of the other RAT
- Maximum number of reported cells
1
- Idle Interval Information
- k
3 (80 ms)
The actual idle interval period equal to 2^k radio frames.
- offset
Not present
Default value is 0
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.15.5 Test requirements
|
Table 8.7.15.5-2 and table 8.7.15.5-3 defines the primary level settings including test tolerances for all tests.
For the test to pass, the ratio of successful reported values according to table 8.7.15.5-4 in each test shall be more than 90%, with a confidence level of 95%.
Table 8.7.15.5-1: Void
Table 8.7.15.5-2: UTRAN TDD cell specific test parameters for E-UTRAN TDD RSRP absolute accuracy tests
Parameter
Unit
Test 1, Test 2
DL timeslot number
0
DwPTS
UTRA RF Channel number Note2
Channel 1
PCCPCH_Ec/Ior
dB
-3
DwPCH_Ec/Ior
dB
0
OCNS_Ec/Ior
dB
-3
Ioc
dBm/1.28MHz
-75
Îor/Ioc
dB
3
PCCPCH RSCP Note1
dBm
-75
Io Note 1
dBm/1.28MHz
-70.24
Propagation condition
AWGN
Note 1: PCCPCH RSCP and Io levels have been calculated from other parameters for information purposes. They are not settable parameters themselves.
Note 2: In the case of multi-frequency network of 1.28 Mcps TDD, the UTRA RF Channel Number can be set for the primary frequency in this test.
Table 8.7.15.5-3: E-UTRAN TDD cell specific test parameters for E-UTRAN TDD RSRP absolute accuracy tests
Parameter
Unit
Test 1
Test 2
E-UTRA RF Channel Number
2
2
BWchannel
MHz
10
10
Measurement bandwidth
22—27
22—27
PDCCH/PCFICH/PHICH Reference measurement channel defined in A.2.2 in TS 36.521-3 [33]
R.6 TDD
R.6 TDD
OCNG Patterns defined in D.2.2 (OP.2 TDD) in TS 36.521-3 [33]
OP.2 TDD
OP.2 TDD
PBCH_RA
dB
0
0
PBCH_RB
PSS_RA
SSS_RA
PCFICH_RB
PHICH_RA
PHICH_RB
PDCCH_RA
PDCCH_RB
PDSCH_RA
PDSCH_RB
OCNG_RANote1
OCNG_RBNote1
Note2
Bands 33 ~ 40
dBm/15 kHz
-88. 95
-117.00
Bands 42 and 43
-116.00
Band 41
-115.00
dB
10.00
-3.20
RSRPNote3
Bands 33 ~ 40
dBm/15 kHz
-78. 95
-120.20
Bands 42 and 43
-119.20
Band 41
-118.20
IoNote3
Bands 33 ~ 40
dBm/9 MHz
-50.75
-87.52
Bands 42 and 43
-86.52
Band 41
-85.52
dB
10.00
-3.20
Propagation condition
-
AWGN
AWGN
Note 1: OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled.
Note 3: RSRP and Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves.
Note 4: RSRP minimum requirements are specified assuming independent interference and noise at each receiver antenna port.
Table 8.7.15.5-4: E-UTRAN TDD RSRP absolute accuracy requirements for the reported values
Test 1
Test 2
All bands
Bands 33 ~ 40
Bands 42 and 43
Band 41
Normal Conditions
Lowest reported value (Cell 2)
RSRP_52
RSRP_13
RSRP_14
RSRP_15
Highest reported value (Cell 2)
RSRP_71
RSRP_28
RSRP_29
RSRP_30
Extreme Conditions
Lowest reported value (Cell 2)
RSRP_49
RSRP_10
RSRP_11
RSRP_12
Highest reported value (Cell 2)
RSRP_74
RSRP_31
RSRP_32
RSRP_33
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.16 E-UTRAN FDD RSRQ
|
Editor’s note: This Test case is incomplete for frequencies above 3GHz
• The Test system uncertainties applicable above 3GHz are undefined
• The Test Tolerances and Test Requirements applicable above 3GHz are undefined
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.16.1 Definition and applicability
|
The absolute accuracy of RSRQ is defined as the RSRQ measured from a cell that has different carrier frequency from the serving cell.
The E-UTRAN FDD RSRQ absolute accuracy measurement is used for handover between UTRAN TDD and E-UTRAN FDD for Rel.9 and later.
The requirements and this test apply to the combined UTRAN TDD and E-UTRAN FDD UE.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.16.2 Minimum Requirements
|
In Cell DCH state, whether or not UE requires idle intervals to perform E-UTRAN measurements, the requirements for accuracy of E-UTRA RSRQ measurements in CELL_DCH state shall be the same as the inter-frequency RSRQ Accuracy Requirements in 3GPP TS 36.133, as follows:
Cell specific reference signals are transmitted either from one, two or four antenna ports.
Conditions defined in 36.101 Section 7.3 for reference sensitivity are fulfilled.
RSRP|dBm according to 36.133 Annex B.3.3 for a corresponding Band
Table 8.7.16.2-1: RSRQ Inter frequency absolute accuracy
Parameter
Unit
Accuracy [dB]
Conditions1
Normal condition
Extreme condition
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23, 24, 33, 34, 35, 36, 37, 38, 39, 40
Bands 2, 5, 7, 41
Band 25
Bands 3, 8, 12, 13, 14, 17, 20, 22
Bands 9, 42, 43
Io
Io
Io
Io
Io
RSRQ when RSRP Ês/Iot > -3 dB
dBm
2.5
4
-121dBm/ 15kHz … -50dBm/ BWChannel
-119dBm/ 15kHz … -50dBm/ BWChannel
-117.5dBm/ 15kHz … -50dBm/ BWChannel
-118dBm/ 15kHz … -50dBm/ BWChannel
-120dBm/ 15kHz … -50dBm/ BWChannel
RSRQ when RSRP Ês/Iot ≥ -6 dB
dBm
3.5
4
-121dBm/ 15kHz … -50dBm/ BWChannel
-119dBm/ 15kHz … -50dBm/ BWChannel
-117.5dBm/ 15kHz … -50dBm/ BWChannel
-118dBm/ 15kHz … -50dBm/ BWChannel
-120dBm/ 15kHz … -50dBm/ BWChannel
Note 1: Io is assumed to have constant EPRE across the bandwidth.
The normative reference for this requirement is TS 25.123 [2] clauses 9.1.1.5b and A.9.2.5b.1.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.16.3 Test purpose
|
The purpose of this test is to verify that the E-UTRA FDD RSRQ measurement absolute accuracy is within the specified limits. This test will verify the requirements in 8.7.16.2 and applies to UE supporting this capability.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.16.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.16.4.1 Initial conditions
|
Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see clauses G.2.1 and G.2.2.
Frequencies to be tested: see table J.2 in Annex J.
In the test in Cell_DCH state, “E-UTRAN FDD RSRQ Measurement” is applied to measure on E-UTRAN FDD.
Tables 8.7.16.4.1-1 and 8.7.16.4.1-2 define the limits of signal strengths and code powers on the UTRA TDD cell. In the measurement control information periodic reporting of E-UTRAN FDD RSRQ is indicated to the UE. The E-UTRAN FDD test parameters are given in Table 8.7.16.4.1-3.
Table 8.7.16.4.1-1: General parameters of E-UTRA FDD RSRQ measurement tests
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Active cell
Cell 1
1.28Mcps TDD cell
Neighbour cell
Cell 2
E-UTRA FDD cell
CP length of cell 2
normal
Idle intervals period
ms
80
As specified in TS 25.331
Filter coefficient
0
L3 filtering is not used
Inter-RAT(E-UTRA FDD) measurement quantity
E-UTRA FDD RSRQ
Table 8.7.16.4.1-2: E-UTRA FDD RSRQ measurement tests parameters (cell 1)
Parameter
Unit
Cell 1
DL timeslot number
0
DwPTS
UTRA RF Channel number (NOTE)
Channel 1
PCCPCH_Ec/Ior
dB
-3
DwPCH_Ec/Ior
dB
0
OCNS_Ec/Ior
dB
-3
Îor/Ioc
dB
3
Ioc
dBm / 1.28MHz
-75
Propagation condition
AWGN
Note: In the case of multi-frequency, the UTRA RF Channel Number can be set for the primary frequency in this test.
Table 8.7.16.4.1-3: E-UTRA FDD RSRQ measurement tests parameters (cell 2)
Parameter
Unit
Test 1
Test 2
Test 3
E-UTRA RF Channel Number
1
1
1
Bwchannel
MHz
10
10
10
Measurement bandwidth
22—27
22—27
22—27
PDCCH/PCFICH/PHICH Reference measurement channel defined in A.2.1 in TS 36.521-3 [33]
R.6 FDD
R.6 FDD
R.6 FDD
OCNG Patterns defined in D.1.1 (OP.1 FDD) and D.1.2 (OP.2 FDD) in TS 36.521-3 [33]
OP.2 FDD
OP.2 FDD
OP.2 FDD
PBCH_RA
dB
0
0
0
PBCH_RB
PSS_RA
SSS_RA
PCFICH_RB
PHICH_RA
PHICH_RB
PDCCH_RA
PDCCH_RB
PDSCH_RA
PDSCH_RB
OCNG_RANote1
OCNG_RBNote1
Note2
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dBm/15 kHz
-80
-104.70
-119.50
Bands 2, 5 and 7
-117.50
Band 25
-116.00
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-116.50
Band 9
-118.50
dB
-1.75
-4.0
-4.0
RSRPNote3
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dBm/15 kHz
-81.75
-108.70
-123.50
Bands 2, 5 and 7
-121.50
Band 25
-120.00
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-120.50
Band 9
-122.50
RSRQNote3
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dB
-14.76
-16.25
-16.25
Bands 2, 5 and 7
Band 25
Bands 3, 8, 12, 13, 14, 17, 20 and 22
Band 9
IoNote3
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dBm/9 MHz
-50
-75.46
-90.26
Bands 2, 5 and 7
-88.26
Band 25
-86.76
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-87.26
Band 9
-89.26
dB
-1.75
-4.0
-4.0
Propagation condition
-
AWGN
AWGN
AWGN
Note 1: OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled.
Note 3: RSRQ, RSRP and Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves.
Note 4: RSRP and RSRQ minimum requirements are specified assuming independent interference and noise at each receiver antenna port.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.16.4.2 Test Procedure
|
1) A call is set up according to the test procedure specified in TS 34.108 [3] clause 7.3.2. The RF parameters for Test 1 are set up according to table 8.7.16.5-2 and 8.7.16.5-3.
2) SS shall transmit the MEASUREMENT CONTROL message for inter RAT measurement. In the measurement control information periodic reporting of the EUTRAN FDD RSRQ is requested to the UE.
3) UE shall transmit periodically MEASUREMENT REPORT messages.
4) SS shall check RSRQ value of Cell 2 in the MEASUREMENT REPORT messages. The RSRQ values of Cell 2 reported by the UE are compared to the actual RSRQ value of Cell 2 for each MEASUREMENT REPORT message.
5) SS shall check MEASUREMENT REPORT messages transmitted by UE until statistical significance according to Annex Tables G.2.3-1 in TS 36.521-3 [33] is achieved.
6) The RF parameters are set up according to tables 8.7.16.5-2 and 8.7.16.5-3 for Test 2 and 3. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 5s and ignore the MEASUREMENT REPORT messages during this period. Then, step 4) and 5) above are repeated.
7) After further 1000 MEASUREMENT REPORT messages have been received from UE, the SS shall transmit RRC CONNECTION RELEASE message.
8) UE shall transmit RRC CONNECTION RELEASE COMPLETE message.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3], with the following exceptions:
Note: Numbers in brackets after an item e.g “Message Type (10.2.17)” in the IE description are references to clause numbers in TS 25.331 [9] describing that item in more detail.
MEASUREMENT CONTROL message for EUTRAN FDD measurement (Step 1):
Information Element
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
-Integrity check info
0
Not Present
Measurement Information elements
-Measurement Identity
-Measurement Command
-Measurement Reporting Mode
- Measurement Report Transfer Mode
- Periodical Reporting / Event Trigger Reporting Mode
-Additional measurement list
-CHOICE Measurement Type
-Inter-frequency measurement object list
-CHOICE Inter-frequency cell removal
-New inter-frequency cells
-Cell for measurement
-Inter-frequency measurement quantity
-CHOICE reporting criteria
-Filter coefficient
-CHOICE mode
-Measurement quantity
-Inter-frequency reporting quantity
-UTRA Carrier RSSI
-Frequency quality estimate
-Non frequency related cell reporting quantities
-SFN-SFN observed time difference reporting indicator
-Cell synchronisation information reporting indicator
-Maximum number of reported cells
-Measurement validity
-Inter-frequency set update
-CHOICE report criteria
-Amount of reporting
-Reporting interval
2
Setup
Acknowledged mode RLC
Periodical reporting
Not Present
Inter-RAT measurement
Not Present
Cell 2 information is included
Not Present
Inter-frequency reporting criteria
0
EUTRAN FDD
RSRQ
FALSE
FALSE
No report
Report all active set cells + cells within monitored set on used frequency
Virtual/active set cells + 1
Not Present
Not Present
Periodical reporting criteria
Infinity
500 ms
Physical channel information elements
-DPCH compressed mode status info
Not Present
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.16.5 Test requirements
|
Table 8.7.16.5-2 and table 8.7.16.5-3 defines the primary level settings including test tolerances for all tests.
For the test to pass, the ratio of successful reported values according to table 8.7.16.5-4 in each test shall be more than 90% with a confidence level of 95%.
Table 8.7.16.5-1: Void
Table 8.7.16.5-2: UTRAN TDD cell specific test parameters for E-UTRAN FDD RSRQ absolute accuracy tests
Parameter
Unit
Cell 1
DL timeslot number
0
DwPTS
UTRA RF Channel number (NOTE)
Channel 1
PCCPCH_Ec/Ior
dB
-3
DwPCH_Ec/Ior
dB
0
OCNS_Ec/Ior
dB
-3
Îor/Ioc
dB
3
Ioc
dBm / 1.28MHz
-75
Propagation condition
AWGN
NOTE: In the case of multi-frequency, the UTRA RF Channel Number can be set for the primary frequency in this test.
Table 8.7.16.5-3: E-UTRAN FDD cell specific test parameters for E-UTRAN FDD RSRQ absolute accuracy tests
Parameter
Unit
Test 1
Test 2
Test 3
E-UTRA RF Channel Number
1
1
1
Bwchannel
MHz
10
10
10
Measurement bandwidth
22—27
22—27
22—27
PDCCH/PCFICH/PHICH Reference measurement channel defined in A.2.1 in TS 36.521-3 [33]
R.6 FDD
R.6 FDD
R.6 FDD
OCNG Patterns defined in D.1.1 (OP.1 FDD) and D.1.2 (OP.2 FDD) in TS 36.521-3 [33]
OP.2 FDD
OP.2 FDD
OP.2 FDD
PBCH_RA
dB
0
0
0
PBCH_RB
PSS_RA
SSS_RA
PCFICH_RB
PHICH_RA
PHICH_RB
PDCCH_RA
PDCCH_RB
PDSCH_RA
PDSCH_RB
OCNG_RANote1
OCNG_RBNote1
Note2
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dBm/15 kHz
-80.80
-104.70
-119.50
Bands 2, 5 and 7
-117.50
Band 25
-116.00
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-116.50
Band 9
-118.50
dB
-1.75
-3.20
-3.20
RSRPNote3
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dBm/15 kHz
-82.55
-107.90
-122.70
Bands 2, 5 and 7
-120.70
Band 25
-119.20
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-119.70
Band 9
-121.70
RSRQNote3
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dB
-14.76
-15.69
-15.69
Bands 2, 5 and 7
Bands 3, 8, 12, 13, 14, 17, 20 and 22
Band 9
IoNote3
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23 and 24
dBm/9 MHz
-50.80
-75.22
-90.02
Bands 2, 5 and 7
-88.02
Band 25
-86.52
Bands 3, 8, 12, 13, 14, 17, 20 and 22
-87.02
Band 9
-89.02
dB
-1.75
-3.20
-3.20
Propagation condition
-
AWGN
AWGN
AWGN
Note 1: OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled.
Note 3: RSRQ, RSRP and Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves.
Note 4: RSRP and RSRQ minimum requirements are specified assuming independent interference and noise at each receiver antenna port.
Table 8.7.16.5-4: E-UTRAN FDD RSRQ absolute accuracy requirements for the reported values
Test 1
Test 2
Test 3
All bands
All bands
Bands 1, 4, 6, 10, 11 18, 19, 21, 23, 24
Bands 2, 5, 7
Band 25
Bands 3, 8, 12, 13, 14, 17, 20, 22
Band 9
Normal Conditions
Lowest reported value (Cell 2)
RSRQ_04
RSRQ_00
RSRQ_00
RSRQ_00
RSRQ_00
RSRQ_00
RSRQ_00
Highest reported value (Cell 2)
RSRQ_16
RSRQ_16
RSRQ_16
RSRQ_16
RSRQ_16
RSRQ_16
RSRQ_16
Extreme Conditions
Lowest reported value (Cell 2)
RSRQ_01
RSRQ_00
RSRQ_00
RSRQ_00
RSRQ_00
RSRQ_00
RSRQ_00
Highest reported value (Cell 2)
RSRQ_19
RSRQ_17
RSRQ_17
RSRQ_17
RSRQ_17
RSRQ_17
RSRQ_17
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.17 E-UTRAN TDD RSRQ
|
Editor’s note: This Test case is incomplete for frequencies above 3GHz
• The Test system uncertainties applicable above 3GHz are undefined
• The Test Tolerances and Test Requirements applicable above 3GHz are undefined
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.17.1 Definition and applicability
|
The absolute accuracy of RSRQ is defined as the RSRQ measured from a cell that has different carrier frequency from the serving cell.
The E-UTRAN TDD RSRQ absolute accuracy measurement is used for handover between UTRAN TDD and E-UTRAN TDD.
The requirements and this test apply to release 9 and later releases UTRA 1.28Mcps TDD UEs that support release 8 and later releases E-UTRA TDD.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.17.2 Minimum Requirements
|
In CELL DCH state, whether or not UE requires idle intervals to perform E-UTRAN measurements, the requirements for accuracy of E-UTRA RSRQ measurements in CELL_DCH state shall be the same as the inter-frequency RSRQ Accuracy Requirements in 3GPP TS 36.133 [26], as follows:
Cell specific reference signals are transmitted either from one, two or four antenna ports.
Conditions defined in TS 36.101 [27] Section 7.3 for reference sensitivity are fulfilled.
RSRP|dBm according to 36.133 Annex B.3.3 for a corresponding Band
Table 8.7.17.2-1: RSRQ Inter frequency absolute accuracy
Parameter
Unit
Accuracy [dB]
Conditions1
Normal condition
Extreme condition
Bands 1, 4, 6, 10, 11, 18, 19, 21, 23, 24, 33, 34, 35, 36, 37, 38, 39, 40
Bands 2, 5, 7, 41
Band 25
Bands 3, 8, 12, 13, 14, 17, 20, 22
Bands 9, 42, 43
Io
Io
Io
Io
Io
RSRQ when RSRP Ês/Iot > -3 dB
dBm
2.5
4
-121dBm/ 15kHz … -50dBm/ BWChannel
-119dBm/ 15kHz … -50dBm/ BWChannel
-117.5dBm/ 15kHz … -50dBm/ BWChannel
-118dBm/ 15kHz … -50dBm/ BWChannel
-120dBm/ 15kHz … -50dBm/ BWChannel
RSRQ when RSRP Ês/Iot ≥ -6 dB
dBm
3.5
4
-121dBm/ 15kHz … -50dBm/ BWChannel
-119dBm/ 15kHz … -50dBm/ BWChannel
-117.5dBm/ 15kHz … -50dBm/ BWChannel
-118dBm/ 15kHz … -50dBm/ BWChannel
-120dBm/ 15kHz … -50dBm/ BWChannel
Note 1: Io is assumed to have constant EPRE across the bandwidth.
The normative reference for this requirement is TS 25.123 [2] clauses 9.1.1.5b and A.9.2.5b.2.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.17.3 Test purpose
|
The purpose of this test is to verify that the E-UTRA TDD RSRQ absolute measurement accuracy is within the specified limits. This test will verify the requirements in section 8.7.17.2 and applies to UE supporting this capability.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.17.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.17.4.1 Initial conditions
|
Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see clauses G.2.1 and G.2.2.
Frequencies to be tested: see table J.2 in Annex J.
In the test in Cell_DCH state, “E-UTRAN TDD RSRQ Measurement” is applied to measure on E-UTRAN TDD.
Tables 8.7.17.4.1-1 and 8.7.17.4.1-2 define the limits of signal strengths and code powers on the UTRA TDD cell. In the measurement control information periodic reporting of E-UTRAN TDD RSRQ is indicated to the UE. The E-UTRAN TDD test parameters are given in Table 8.7.17.4.1-3.
Table 8.7.17.4.1-1: General parameters of E-UTRA TDD RSRQ measurement tests
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in section C.3.1
Power Control
On
Target quality value on DTCH
BLER
0.01
Active cell
Cell 1
1.28Mcps UTRA TDD cell
Neighbour cell
Cell 2
E-UTRA TDD cell
CP length of cell 2
Normal
Uplink-downlink configuration of cell 2
1
As specified in table 4.2.2 in TS 36.211 [30]
Special subframe configuration of cell 2
6
As specified in table 4.2.1 in TS 36.211 [30]
Idle intervals period
ms
80
As specified in TS 25.331 [9]
Filter coefficient
0
L3 filtering is not used
Inter-RAT(E-UTRA TDD) measurement quantity
E-UTRA TDD RSRQ
Table 8.7.17.4.1-2: E-UTRA TDD RSRQ measurement tests parameters (cell 1)
Parameter
Unit
Test 1, Test 2, and Test 3
DL timeslot number
0
DwPTS
UTRA RF Channel number Note2
Channel 1
PCCPCH_Ec/Ior
dB
-3
DwPCH_Ec/Ior
dB
0
OCNS_Ec/Ior
dB
-3
Ioc
dBm/1.28MHz
-75
Îor/Ioc
dB
3
PCCPCH RSCP Note1
dBm
-75
Io Note 1
dBm/1.28MHz
-70.24
Propagation condition
AWGN
Note 1: PCCPCH RSCP and Io levels have been calculated from other parameters for information purposes. They are not settable parameters themselves.
Note 2: In the case of multi-frequency network of 1.28 Mcps TDD, the UTRA RF Channel Number can be set for the primary frequency in this test.
Table 8.7.17.4.1-3: E-UTRA TDD RSRQ measurement tests parameters (cell 2)
Parameter
Unit
Test 1
Test 2
Test 3
E-UTRA RF Channel Number
2
2
2
BWchannel
MHz
10
10
10
Measurement bandwidth
22—27
22—27
22—27
PDCCH/PCFICH/PHICH Reference measurement channel defined in A.2.2 in TS 36.521-3 [33]
R.6 TDD
R.6 TDD
R.6 TDD
OCNG Patterns defined in D.2.2 (OP.2 TDD) in TS 36.521-3 [33]
OP.2 TDD
OP.2 TDD
OP.2 TDD
PBCH_RA
dB
0
0
0
PBCH_RB
PSS_RA
SSS_RA
PCFICH_RB
PHICH_RA
PHICH_RB
PDCCH_RA
PDCCH_RB
PDSCH_RA
PDSCH_RB
OCNG_RANote1
OCNG_RBNote1
Note2
Bands 33 – 40
dBm/15 kHz
-80
-104.70
-119.50
Band 42 and 43
-118.50
Band 41
-117.50
dB
-1.75
-4.0
-4.0
RSRPNote3
Bands 33 – 40
dBm/15 kHz
-81.75
-108.70
-123.50
Band 42 and 43
-122.50
Band 41
-121.50
RSRQNote3
Bands 33 – 43
dB
-14.76
-16.25
-16.25
IoNote3
Bands 33 – 40
dBm/9 MHz
-50
-75.46
-90.26
Bands 42 and 43
-89.26
Bands 41
-88.26
dB
-1.75
-4.0
-4.0
Propagation condition
-
AWGN
AWGN
AWGN
Note 1: OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled.
Note 3: RSRP, RSRQ and Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves.
Note 4: RSRP and RSRQ minimum requirements are specified assuming independent interference and noise at each receiver antenna port.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.17.4.2 Test Procedure
|
1) A call is set up according to the test procedure specified in TS 34.108 [3] clause 7.3.2. The RF parameters for Test 1 are set up according to tables 8.7.17.5-2 and 8.7.17.5-3.
2) SS shall transmit the MEASUREMENT CONTROL message for inter RAT measurement. In the measurement control information periodic reporting of the EUTRAN TDD RSRQ is requested to the UE.
3) After sending the measurement control message, wait for 10s, then the UE shall transmit periodically MEASUREMENT REPORT messages.
4) After the 10s wait in step 3), SS shall check E-UTRAN TDD RSRQ value of Cell 2 in periodical MEASUREMENT REPORT messages. E-UTRAN TDD RSRQ values of Cell 2 reported by UE is compared to actual E-UTRAN TDD RSRQ value of Cell 2 for each MEASUREMENT REPORT message. If the UE fails to report the measurement values including neighbour cell RSRQ, the number of failures is increased by one.
5) SS shall check MEASUREMENT REPORT messages transmitted by UE until statistical significance according to Tables G.2.3-1 in TS 36.521-3 [33] is achieved.
6) The RF parameters are set up according to tables 8.7.17.5-2 and 8.7.17. 5-3 for Test 2. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 5s and ignore the MEASUREMENT REPORT messages during this period. Then, step 3) to 5) above are repeated.
7) The RF parameters are set up according to tables 8.7.17.5-2 and 8.7.17. 5-3 for Test 3. While RF parameters are being set up, MEASUREMENT REPORT messages from UE are ignored. SS shall wait for additional 5s and ignore the MEASUREMENT REPORT messages during this period. Then, step 3) to 5) above are repeated.
8) The SS shall transmit RRC CONNECTION RELEASE message.
9) UE shall transmit RRC CONNECTION RELEASE COMPLETE message.
Specific Message Contents
All messages indicated above shall use the same content as described in default message content in clause 9 of TS 34.108 [3] and clause 4.4 and 4.7B.1 of TS 36.508 [28], with the following exceptions:
MEASUREMENT CONTROL message for EUTRAN TDD measurement (Step 1):
Derivation Path: TS 36.508 [28], clause 4.7B.1 Table 4.7B.1-3: MEASUREMENT CONTROL
Information Element
Value/remark
Comment
Condition
Message Type
RRC transaction identifier
0
Measurement Identity
2
Measurement Reporting Mode
- Measurement Report Transfer Mode
Acknowledged mode RLC
- Periodical Reporting/Event Trigger Reporting Mode
Periodical reporting
CHOICE Measurement type
Inter-RAT measurement
- CHOICE Inter-RAT measurement objects
E-UTRA frequency list
- New frequencies
- E-UTRA carrier frequency
Downlink EARFCN of E-UTRA Cell
- Measurement bandwidth
mbw6
- Inter-RAT measurement quantity
- Measurement quantity for UTRAN quality estimate
- Filter coefficient
0
- CHOICE mode
TDD
TDD_UTRA
- Measurement quantity
Primary CCPCH RSCP
- CHOICE system
E-UTRA
- Measurement quantity
RSRQ
- Filter coefficient
0
- CHOICE report criteria
Periodical reporting criteria
- Periodical reporting criteria
- Amount of reporting
Infinity
- Reporting interval
500 ms
- Reporting cell status
- CHOICE reported cell
Report cells within active set or within virtual active set or of the other RAT
- Maximum number of reported cells
1
- Idle Interval Information
- k
3 (80 ms)
The actual idle interval period equal to 2^k radio frames.
- offset
Not present
Default value is 0.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
8.7.17.5 Test requirements
|
Table 8.7.17.5-2 and table 8.7.17.5-3 defines the primary level settings including test tolerances for all tests.
For the test to pass, the ratio of successful reported values according to table 8.7.17.5-4 in each test shall be more than 90% with a confidence of 95%.
Table 8.7.17.5-1: Void
Table 8.7.17.5-2: UTRAN TDD cell specific test parameters for E-UTRAN TDD RSRQ absolute accuracy tests
Parameter
Unit
Test 1, Test 2, and Test 3
DL timeslot number
0
DwPTS
UTRA RF Channel number Note2
Channel 1
PCCPCH_Ec/Ior
dB
-3
DwPCH_Ec/Ior
dB
0
OCNS_Ec/Ior
dB
-3
Ioc
dBm/1.28MHz
-75
Îor/Ioc
dB
3
PCCPCH RSCP Note1
dBm
-75
Io Note 1
dBm/1.28MHz
-70.24
Propagation condition
AWGN
Note 1: PCCPCH RSCP and Io levels have been calculated from other parameters for information purposes. They are not settable parameters themselves.
Note 2: In the case of multi-frequency network of 1.28 Mcps TDD, the UTRA RF Channel Number can be set for the primary frequency in this test.
Table 8.7.17.5-3: E-UTRAN TDD cell specific test parameters for E-UTRAN TDD RSRQ absolute accuracy tests
Parameter
Unit
Test 1
Test 2
Test 3
E-UTRA RF Channel Number
2
2
2
BWchannel
MHz
10
10
10
Measurement bandwidth
22—27
22—27
22—27
PDCCH/PCFICH/PHICH Reference measurement channel defined in A.2.2 in TS 36.521-3 [33]
R.6 TDD
R.6 TDD
R.6 TDD
OCNG Patterns defined in D.2.2 (OP.2 TDD) in TS 36.521-3 [33]
OP.2 TDD
OP.2 TDD
OP.2 TDD
PBCH_RA
dB
0
0
0
PBCH_RB
PSS_RA
SSS_RA
PCFICH_RB
PHICH_RA
PHICH_RB
PDCCH_RA
PDCCH_RB
PDSCH_RA
PDSCH_RB
OCNG_RANote1
OCNG_RBNote1
Note2
Bands 33 – 40
dBm/15 kHz
-80.80
-104.70
-119.50
Band 42 and 43
-118.50
Band 41
-117.50
dB
-1.75
-3.20
-3.20
RSRPNote3
Bands 33 – 40
dBm/15 kHz
-82.55
-107.90
-122.70
Band 42 and 43
-121.70
Band 41
-120.70
RSRQNote3
Bands 33 – 40
dB
-14.76
-15.69
-15.69
IoNote3
Bands 33 – 40
dBm/9 MHz
-50.80
-75.22
-90.02
Band 42 and 43
-89.02
Band 41
-88.02
dB
-1.75
-3.20
-3.20
Propagation condition
-
AWGN
AWGN
AWGN
Note 1: OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled.
Note 3: RSRP, RSRQ and Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves.
Note 4: RSRP and RSRQ minimum requirements are specified assuming independent interference and noise at each receiver antenna port.
Table 8.7.17.5-4: E-UTRAN TDD RSRQ absolute accuracy requirements for the reported values
Test 1
Test 2
Test 3
All bands
All bands
Bands 33 ~ 40
Bands 42, 43
Bands 41
Normal Conditions
Lowest reported value (Cell 2)
RSRQ_04
RSRQ_00
RSRQ_00
RSRQ_00
RSRQ_00
Highest reported value (Cell 2)
RSRQ_16
RSRQ_16
RSRQ_16
RSRQ_16
RSRQ_16
Extreme Conditions
Lowest reported value (Cell 2)
RSRQ_01
RSRQ_00
RSRQ_00
RSRQ_00
RSRQ_00
Highest reported value (Cell 2)
RSRQ_19
RSRQ_17
RSRQ_17
RSRQ_17
RSRQ_17
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
9 Performance requirements for HSDPA
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.1 General
|
Receiving performance test of the UE is implemented during communicating with the SS via air interface. The procedure uses normal call protocol until the UE is communicating on traffic channel basically. (Refer to TS 34.108 [3] Common Test Environments for User Equipment (UE) Conformance Testing.) On the traffic channel, the UE provides special function for testing that is described in Logical Test Interface and the UE is tested using this function. (Refer to TS 34.109 [4] Logical Test Interface (FDD/TDD) Special conformance testing functions).
Unless otherwise stated the receiver characteristics are specified at the antenna connector of the UE. For UE(s) with an integral antenna only, a reference antenna with a gain of 0 dBi is assumed. UE with an integral antenna may be taken into account by converting these power levels into field strength requirements, assuming a 0 dBi gain antenna. Receiver characteristics for UE(s) with multiple antennas/antenna connectors are for further study.
The UE antenna performance has a significant impact on system performance, and minimum requirements on the antenna efficiency are therefore intended to be included in future versions of the present document. It is recognized that different requirements and test methods are likely to be required for the different types of UE.
All Bit Error ratio (BER) measurements shall be performed according to the general rules for statistical testing in Annex F.6.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2 Performance requirement for 3.84 Mcps TDD option
|
During the Fixed Reference Channel tests the behaviour of the Node-B emulator in response to the ACK/NACK signalling field of the HS-DPCCH is specified in Table 9.2.1:
Table 9.2.1: Node-B Emulator Behaviour in response to ACK/NACK/DTX
0 HS-DPCCH ACK/NACK Field State
0 Node-B Emulator Behaviour
1 ACK
1 ACK: new transmission using 1st redundancy and constellation version (RV)
2 NACK
2 NACK: retransmission using the next RV (up to the maximum permitted number or RV’s)
3 DTX
3 DTX: retransmission using the RV previously transmitted to the same H-ARQ process
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.1 HS-DSCH throughput for Fixed Reference Channels
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.1.1 Definition and applicability
|
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 3.84 Mcps TDD UE from release 5 and later that support HSDPA.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.1.2 Minimum requirements
|
The requirements are specified in terms of minimum information bit throughput R for the DL reference channels specified in Annex C.4.1 with the addition of the relevant parameters in Tables 9.2.1.1 and 9.2.1.3.
Using this configuration the throughput shall meet or exceed the minimum requirements specified in tables 9.2.1.2 and 9.2.1.4.
Table 9.2.1.1: Test parameters for fixed reference measurement channel requirements for 7,3 Mbps – Category 8 - UE (3,84 Mcps TDD Option) QPSK
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
HS-PDSCH Modulation
-
QPSK
Scrambling code and basic midamble code number*
-
0, 1
Number of TS
-
8
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..16
C(i,16)
i=1..14
Number of Hybrid ARQ processes
-
4
Maximum number of Hybrid ARQ transmissions
-
4
Redundancy and constellation version coding sequence**
-
{0,0,0,0}
s=1, R=0, b=0
dB
-12,04
-11.46
dB
0
Ioc
dBm/3,84MHz
-60
Note *: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Note **: This sequence implies Chase combining
Table 9.2.1.2: Performance requirements for fixed reference measurement channel requirement in multipath channels for 7,3 Mbps – Category 8 - UE (3,84 Mcps TDD Option) QPSK
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
8,5
1300
2
PB3
9,0
1300
3
VA30
9,75
1300
4
VA120
11,5
1400
Table 9.2.1.3: Test parameters for fixed reference measurement channel requirements for 7,3 Mbps – Category 8 - UE (3,84 Mcps TDD Option) 16QAM
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
HS-PDSCH Modulation
-
16QAM
Scrambling code and basic midamble code number*
-
0, 1
Number of TS
-
8
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..16
C(i,16)
i=1..14
Number of Hybrid ARQ processes
-
4
Maximum number of Hybrid ARQ transmissions
-
4
Redundancy and constellation version coding sequence**
-
{0,0,0,0}
s=1, r=0
dB
-12,04
-11,46
dB
0
Ioc
dBm/3,84MHz
-60
Note *: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Note **: This sequence implies Chase combining
Table 9.2.1.4: Performance requirements for fixed reference measurement channel requirement in multipath channels for 7,3 Mbps – Category 8 - UE (3,84 Mcps TDD Option) 16QAM
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
16,0
2600
2
PB3
17,5
2600
3
VA30
18,5
2600
4
VA120
14,5
1600
The reference for this requirement is TS 25.102 [1] clauses 9.1.1.1 and 9.1.1.2.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.1.3 Test purpose
|
To verify the ability of the receiver to receive a predefined test signal, representing a multi-path fading channel with information bit throughput R not falling below a specified value.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.1.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.1.4.1 Initial conditions
|
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS (node B emulator) and fader and AWGN noise source to the UE antenna connector as shown in figure A.10.
2) Set up an HSDPA call according to TS 34.108 [3] clause 7.3.6.3 with levels according to Annex E.3.
3) Set the node B emulator ACK/NACK/DTX behaviour according to table 9.2.1. Set the test parameters and levels for tests 1-4 according to tables 9.2.1.1. The reference channel configuration is defined in section C.4.1. The configuration of the TX power for downlink physical channels is annex in E.3.
4) The information bit data shall be pseudo random and not repeated before 10 different information bit payload blocks are processed. (e.g. Fixed reference Channel Definition (16 QAM, test 1,2,3): The information bit payload block is 52996 bits long. Hence the PRBSequence must be at least 52996 * 10 bits long. ) Use a PRBS from ITU-T O.153 Ref [25].
5) Setup the fading simulator with fading conditions as described in table D.2.2.1A.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.1.4.2 Procedure
|
a. Once the HSDPA connection is setup, start transmitting HSDPA data.
b. For all relevant propagation conditions, for all relevant Ioc levels, for all relevant Ec/Ior, for all relevant Îor/Ioc defined in Tables 9.2 and 9.4 count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3 tables F.6.3.5.3 and F.6.3.5.4.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.1.5 Test Requirements
|
Tables 9.2.1.1 to 9.2.1.4 define the primary level settings including test tolerance for all relevant throughput tests. The pass / fail decision for throughput is done according to Annex F.6.3.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.2 HS-DSCH throughput for Variable Reference Channels
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.2.1 Definition and applicability
|
The HS-DSCH data throughput for variable reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 3.84 Mcps TDD UE from release 5 and later that support HSDPA.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.2.2 Minimum requirements
|
For the parameters specified in Table 9.2.2.1 the measured throughput R shall exceed the throughput specified in Table 9.2.2.2 for each radio condition. The variable Reference Channel is specified in Annex C.4.3.
Table 9.2.2.1: Test parameters for variable reference measurement channel requirements for 7,3 Mbps – Category 8 - UE (3,84 Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Scrambling code and basic midamble code number*
-
0, 1
Number of TS
-
8
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..16
Number of Hybrid ARQ processes**
-
4
Maximum number of Hybrid ARQ transmissions
-
1
Redundancy and constellation version coding sequence
(Xrv, s, r, b)
(0, 1, 0, 0)
HS-PDSCHi_Ec/Ior
dB
–12,04
dB
0
Ioc
dBm/3,84MHz
-60
Note *: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Note **: For timing requirements, HARQ is not active
Table 9.2.2.2: Performance requirements for variable reference measurement channel requirement in multipath channels for 7,3 Mbps – Category 8 - UE (3,84 Mcps TDD Option)
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
8,8
1240
14,8
2500
18,8
3600
24,8
5000
2
PB3
8,8
1220
14,8
2430
20,8
4030
24,8
5080
3
VA30
10,1
1190
16,1
2290
20,1
3220
24,1
4260
4
VA120
7,1
590
11,1
1180
15,1
1840
19,1
2390
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.2.3 Test purpose
|
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, with the selection of QPSK and 16QAM modulation, and appropriate blocksize being determined by the SS based on the CQI reported by the UE..
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.2.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.2.4.1 Initial conditions
|
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS (node B emulator) and fader and AWGN noise source to the UE antenna connector as shown in figure A.10.
2) Set up an HSDPA call according to TS 34.108 [3] clause 7.3.6.3 with levels according to Annex E.3.
3) Set the node B emulator ACK/NACK/DTX behaviour according to table 9.2.1. Set the test parameters and levels for tests 1-4 according to tables 9.2.2.1. The reference channel configuration is defined in section C.4.3. The configuration of the TX power for downlink physical channels is annex in E.3.
4) The information bit data shall be pseudo random and not repeated before 10 different information bit payload blocks are processed. Use a PRBS from ITU-T O.153 Ref [25]
5) Setup the fading simulator with fading conditions as described in table D.2.2.1A.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.2.4.2 Procedure
|
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The SS shall transmit a HSDPA block to UE selecting any TBS value,then SS will decode the CQI report and transmit a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.
3) For any HSDPA block transmitted by the SS, record transmitted block size and relevant received ACK, NACK and statDTX reported by UE. If UE reports ACK,the transmitted block is correctly received by UE.Continue transmission of the HS-PDSCH data and record transmitted block size until [2000] records have been reached.
4) For all relevant propagation conditions ,calculate the throughput, which is the ratio of the sum of correctly received transport bits over the testing time. [2000] multiplied by transmission time interval is the testing time.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.2.5 Test Requirements
|
Table 9.2.2.1 define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.2.2.2.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.3 Reporting of HS-DSCH Channel Quality Indicator
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.3.1 Definition and applicability
|
The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 3.84 Mcps TDD UE from release 5 and later that support HSDPA.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.3.2 Minimum requirements
|
For the parameters specified in Table 9.2.3.1, the reported CQI value shall be in the range of +/-10 of the reported median more than 90% of the time. The BLER for the reported median CQI shall be less than 10%.
Table 9.2.3.1: Test parameters for variable reference measurement channel requirements for 7,3 Mbps – Category 8 - UE (3,84 Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Scrambling code and basic midamble code number*
-
0, 1
Number of TS
-
8
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..16
Number of Hybrid ARQ processes**
-
4
Maximum number of Hybrid ARQ transmissions
-
1
Redundancy and constellation version coding sequence
(Xrv, s, r, b)
(0, 1, 0, 0)
HS-PDSCHi_Ec/Ior
dB
–12,04
dB
0
dB
5
10
Ioc
dBm/3,84MHz
-60
Note*: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Note**: For timing requirements, HARQ is not active
Table 9.3.3.2 Performance requirements for CQI reporting measurement channel requirements for 7.3 Mbps – Category 9- UE (3.84 Mcps TDD Option)
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 10
90
10%
Test 2
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.3.3 Test purpose
|
To verify that the variance of the CQI reports in an AWGN channel is within the limits defined and that a BLER of better than 10% is obtained for the median reported CQI.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.3.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.3.4.1 Initial conditions
|
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS and an AWGN source to the UE antenna connector as shown in figure A.9.
2) Set up an HSDPA call according to TS 34.108 [3] clause 7.3.6.3 with levels according to Annex E.3.
3) Set the node B emulator ACK/NACK/DTX behaviour according to table 9.2.1. Set the test parameters and levels for tests 1-2 according to tables 9.2.3.1. The reference channel configuration is defined in section C.4.1. The configuration of the TX power for downlink physical channels is annex in E.3.
4) The information bit data shall be pseudo random and not repeated before 10 different information bit payload blocks are processed. (e.g. Fixed reference Channel Definition (16 QAM, test 1,2,3): The information bit payload block is 52996 bits long. Hence the PRBSequence must be at least 52996 * 10 bits long. ) Use a PRBS from ITU-T O.153 Ref [25].
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.3.4.2 Procedure
|
Note: the following part of the procedure will test, if the UE reports a limited range of CQI indicator under the predefined channel conditions.
1) The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0,then SS will decodes the CQI report and transmits a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.For any HSDPA block transmitted by the SS, record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of the HS-PDSCH data and collect RTBS value of CQI until [2000] reports have been gathered.
2) Set up a relative frequency distribution for the RTBS value of CQI indicator reported. Calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side). This RTBS value of CQI indicator is declared as Median CQI value,
3) If [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI - 10) ≤ Median CQI ≤ ( Median CQI + 10) then continue with next step , otherwise fail the UE.
4) Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
5) Repeat the same procedure (steps 2 to 5 ) with test conditions according to the table 9.3.3.1 for Test 2, Test 3 and Test 4
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.3.5 Test Requirements
|
The pass fail decision as specified in the test procedure in 9.3.1.4.2.
No test tolerance is applied to the test parameters.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.4 HS-SCCH Detection Performance
|
void
9.2.4A HS-SCCH Detection Performance
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.4.1 Definition and applicability
|
The detection performance of the HS-SCCH is determined by the probability of event Em, which is declared when the UE is signaled on HS-SCCH, but DTX is observed in the corresponding HS-SICH ACK/NACK field. The probability of event Em is denoted P(Em).
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 3.84 Mcps TDD UE from release 5 and later that support HSDPA.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.4.2 Minimum requirements
|
For the test parameters in Table 9.2.4.1, for each value of HS-SCCH-1 Ec/Ior specified in Table 9.2.4.2, the measured P(Em) shall be less than or equal to the corresponding specified value of P(Em).
Table 9.2.4.1: Test parameters for HS-SCCH detection (3.84 Mcps TDD option)
Parameter
Unit
Test 1
Test 2
Test 3
Number of TS under test
-
1
Number of HS-SCCH codes per timeslot
-
4
HS-SCCH UE Identity
(,, …, )
-
UE1 = 0000000000000000
(UE1 under test)
UE2 = 0101010101010101
UE3 = 1010101010101010
UE4 = 1111111111111111
HS-SCCH Channelization Codes*
C(k,Q)
HS-SCCH-1 = C(1, 16), for UE1 (UE under test)
HS-SCCH-2 = C(2, 16) for UE2
HS-SCCH-3 = C(3, 16) for UE3
HS-SCCH-4 = C(4, 16) for UE4
HS-SCCH Ec/Ior
dB
HS-SCCH-2_Ec/Ior = HS-SCCH-3_Ec/Ior = HS-SCCH-4_Ec/Ior,
Where, HS-SCCH-X_Ec/Ior = 1, where X = 1, 2, 3, 4
Table 9.2.4.2: Minimum requirement for HS-SCCH detection (3.84 Mcps TDD option)
Test Number
Propagation Conditions
Reference value
HS-SCCH-1
(dB)
(dB)
1
PA3
-1.6
0
0.05
2
PA3
-3.0
5
0.01
3
VA30
-2.5
0
0.01
The reference for this requirement is TS 25.102 [2] clause 9.1.4.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.4.3 Test purpose
|
To verify that P(Em) does not exceed the limit in table 9.2.4.2.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.4.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.4.4.1 Initial conditions
|
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect SS, multipath fading simulator and an AWGN noise source to the UE antenna connector as shown in figure A.10.
2. Setup fading simulators as fading condition, which are described in table D.2.2.1A.
3. Set the node B emulator ACK/NACK/DTX behaviour according to table 9.2.1. Set the test parameters and levels for tests 1-3 according to tables 9.2.4.1 and 9.2.4.2. The reference channel configuration is defined in section C.4.1. The configuration of the TX power for downlink physical channels is annex in E.3.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.4.4.2 Procedure
|
1. The UE is switched on.
2. Set up an HSDPA call according to TS 34.108 [3] clause 7.3.6.3.
3. Count the number of NACK, ACK and statDTX on the UL HS-DPCCH during the test interval and decide pass or fail according to Annex F.6.1 and table F.6.1.8. NACK and ACK are counted as a pass and statDTX is counted as a failure.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.2.4.5 Test Requirements
|
The probability of event Em denoted as P(Em) (test procedure step 3) shall not exceed the specified value in table 9.2.4.2.
No test tolerance is applied to the test parameters.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3 Performance requirements for 1.28 Mcps TDD option
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.1 HS-DSCH throughput for Fixed Reference Channels
|
The overall performance metric for HS-DSCH requirements is the throughput “R” measured on HS-DSCH.
During the Fixed Reference Channel tests the behaviour of the Node-B emulator in response to the ACK/NACK signalling field of the HS-SICH is specified in Table 9.3.1.1:
Table 9.3.1.1: Node-B Emulator Behaviour in response to ACK/NACK/DTX (Fixed reference channel)
HS-DPCCH ACK/NACK Field State
Node-B Emulator Behaviour
ACK
ACK: new transmission using 1st redundancy version (RV)
NACK
NACK: retransmission using the next RV (up to the maximum permitted number or RV’s)
DTX
DTX: retransmission using the RV previously transmitted to the same H-ARQ process
9.3.1A HS-DSCH throughput for Fixed Reference Channels 0.5 Mbps UE class QPSK
9.3.1A.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 0.5 Mbps UE class.
9.3.1A.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows table specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1A.1: Test parameters for fixed reference measurement channel requirements for 0.5 Mbps UE class QPSK
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
HS-PDSCH Modulation
-
QPSK
Scrambling code and basic midamble code number*
-
1
Midamble
Common midamble
Number of TS**
2
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..10
Number of Hybrid ARQ processes
-
4
Maximum number of Hybrid ARQ transmissions
-
4
Redundancy and constellation version coding sequence
-
{0,0,0,0}
dB
-10
Ioc
dBm/1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
**Note: The timeslot just after the second switch point should be included.
Table 9.3.1A.2: Minimum performance requirements for fixed reference measurement channel requirement in multipath channels for 0.5Mbps UE class QPSK
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10
160
2
PB3
10
170
3
VA30
10
161
4
VA120
10
153
9.3.1A.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above for QPSK modulation.
9.3.1A.4 Method of test
9.3.1A.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1A.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. (e.g. Fixed reference Channel Definition (16 QAM): The information bit payload block is 3650 bits long. Hence the PRBSequence must be at least 3650 * 10 bits long. ) Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3, table F.6.3.5.1..
9.3.1A.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.1A.3 of test requirement.
Table 9.3.1A.3: Test requirements for fixed reference measurement channel requirement in multipath channels for 0.5Mbps UE class QPSK
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10.6
160
2
PB3
10.6
170
3
VA30
10.6
161
4
VA120
10.6
153
The pass / fail decision for throughput is done according to Annex F.6.3.9.3.1B HS-DSCH throughput for Fixed Reference Channels 1.1 Mbps UE class 16QAM
9.3.1B.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 1.1 Mbps UE class..
9.3.1B.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows table specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1B.1: Test parameters for fixed reference measurement channel requirements for 1.1 Mbps UE class, 16QAM
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
HS-PDSCH Modulation
-
16QAM
Scrambling code and basic midamble code number*
-
1
Midamble
Common midamble
Number of TS**
-
2
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..12
Number of Hybrid ARQ processes
-
4
Maximum number of Hybrid ARQ transmissions
-
4
Redundancy and constellation version coding sequence
-
{6,2,1,5}
dB
-10.8
Ioc
dBm/1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
**Note: The timeslot just after the second switch point should be included.
Table 9.3.1B.2: Minimum performance requirements for fixed reference measurement channel requirement in multipath channels for 1.1Mbps UE class, 16QAM
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15
388
2
PB3
15
347
3
VA30
15
316
4
VA120
15
274
9.3.1B.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above for 16QAM modulation.
9.3.1B.4 Method of test
9.3.1B.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1B.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. (e.g. Fixed reference Channel Definition (16 QAM): The information bit payload block is 3650 bits long. Hence the PRBSequence must be at least 3650 * 10 bits long. ) Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3, table F.6.3.5.2.
9.3.1B.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.1B.3 of test requirement.
Table 9.3.1B.3: Test requirements for fixed reference measurement channel requirement in multipath channels for 1.1Mbps UE class, 16QAM
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15.6
388
2
PB3
15.6
347
3
VA30
15.6
316
4
VA120
15.6
274
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1C HS-DSCH throughput for Fixed Reference Channels 1.6 Mbps UE class QPSK/16QAM
9.3.1C.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 1.6 Mbps UE class..
9.3.1C.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows table specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1C.1: Test parameters for fixed reference measurement channel requirements for 1.6 Mbps UE class
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Test 5
Test 6
Test 7
Test 8
HS-PDSCH Modulation
-
QPSK
16QAM
Scrambling code and basic midamble code number*
-
1
Midamble
Common midamble
Number of TS**
-
3
Number of Hybrid ARQ processes
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..10
C(i,16)
i=1..12
Redundancy and constellation version coding sequence
-
{0,0,0,0}
{6,2,1,5}
dB
-10
-10.8
Ioc
dBm/
1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
**Note: The timeslot just after the second switch point should be included.
Table 9.3.1C.2: Minimum performance requirements for fixed reference measurement channel requirement in multipath channels for 1.6Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10
270
2
PB3
10
278
3
VA30
10
259
4
VA120
10
242
5
PA3
15
488
6
PB3
15
471
7
VA30
15
431
8
VA120
15
377
9.3.1C.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above for QPSK and 16QAM modulation.
9.3.1C.4 Method of test
9.3.1C.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1C.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. (e.g. Fixed reference Channel Definition (16 QAM): The information bit payload block is 3650 bits long. Hence the PRBSequence must be at least 3650 * 10 bits long. ) Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3, tables F.6.3.5.3 and F.6.3.5.4.
9.3.1C.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.1C.3 of test requirement.
Table 9.3.1C.3: Test requirements for fixed reference measurement channel requirement in multipath channels for 1.6Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10.6
270
2
PB3
10.6
278
3
VA30
10.6
259
4
VA120
10.6
242
5
PA3
15.6
488
6
PB3
15.6
471
7
VA30
15.6
431
8
VA120
15.6
377
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1D HS-DSCH throughput for Fixed Reference Channels 2.2 Mbps UE class QPSK/16QAM
9.3.1D.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 2.2 Mbps UE class..
9.3.1D.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows table specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1D.1: Test parameters for fixed reference measurement channel requirements for 2.2 Mbps UE class
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Test 5
Test 6
Test 7
Test 8
HS-PDSCH Modulation
-
QPSK
16QAM
Scrambling code and basic midamble code number*
-
1
Minimum
Common midamble
Number of TS**
-
4
Number of Hybrid ARQ processes
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..10
C(i,16)
i=1..12
Redundancy and constellation version coding sequence
-
{0,0,0,0}
{6,2,1,5}
dB
-10
-10.8
Ioc
dBm/
1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
**Note: The timeslot just after the second switch point should be included.
Table 9.3.1D.2: Minimum performance requirements for fixed reference measurement channel requirement in multipath channels for 2.2Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10
360
2
PB3
10
343
3
VA30
10
320
4
VA120
10
275
5
PA3
15
615
6
PB3
15
606
7
VA30
15
554
8
VA120
15
493
9.3.1D.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above for QPSK and 16QAM modulation.
9.3.1D.4 Method of test
9.3.1D.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1D.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. (e.g. Fixed reference Channel Definition (16 QAM): The information bit payload block is 3650 bits long. Hence the PRBSequence must be at least 3650 * 10 bits long. ) Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3, tables F.6.3.5.5 and F.6.3.5.6.
9.3.1D.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.1D.3 of test requirement.
Table 9.3.1D.3: Test requirements for fixed reference measurement channel requirement in multipath channels for 2.2Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10.6
360
2
PB3
10.6
343
3
VA30
10.6
320
4
VA120
10.6
275
5
PA3
15.6
615
6
PB3
15.6
606
7
VA30
15.6
554
8
VA120
15.6
493
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1E HS-DSCH throughput for Fixed Reference Channels 2.8 Mbps UE class QPSK/16QAM
9.3.1E.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 2.8 Mbps UE class..
9.3.1E.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows table specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1E.1: Test parameters for fixed reference measurement channel requirements for 2.8 Mbps UE class
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Test 5
Test 6
Test 7
Test 8
HS-PDSCH Modulation
-
QPSK
16QAM
Scrambling code and basic midamble code number*
-
1
Midamble
Common midamble
Number of TS
-
5
Number of Hybrid ARQ processes
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..10
C(i,16)
i=1..12
Redundancy and constellation version coding sequence
-
{0,0,0,0}
{6,2,1,5}
dB
-10
-10.8
Ioc
dBm/
1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.1E.2: Minimum performance requirements for fixed reference measurement channel requirement in multipath channels for 2.8Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10
461
2
PB3
10
470
3
VA30
10
438
4
VA120
10
409
5
PA3
15
890
6
PB3
15
810
7
VA30
15
730
8
VA120
15
630
9.3.1E.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above for QPSK and 16QAM modulation.
9.3.1E.4 Method of test
9.3.1E.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1E.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. (e.g. Fixed reference Channel Definition (16 QAM): The information bit payload block is 3650 bits long. Hence the PRBSequence must be at least 3650 * 10 bits long. ) Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3, tables F.6.3.5.7and F.6.3.5.8.
9.3.1E.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.1E.3 of test requirement.
Table 9.3.1E.3: Test requirements for fixed reference measurement channel requirement in multipath channels for 2.8Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10.6
461
2
PB3
10.6
470
3
VA30
10.6
438
4
VA120
10.6
409
5
PA3
15.6
890
6
PB3
15.6
810
7
VA30
15.6
730
8
VA120
15.6
630
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1F HS-DSCH throughput for Fixed Reference Channels Categories 16-18- 64QAM
The overall performance metric for HS-DSCH requirements is the throughput “R” measured on HS-DSCH.
9.3.1F.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 8 and later that support HSDPA UE capability categories 16 - 24.
9.3.1F.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows table specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1F.1: Test parameters for fixed reference measurement channel requirements for category 16-18 UE
Parameters
Unit
Test 1
(Category 16-18)
HS-PDSCH Modulation
-
64QAM
Scrambling code and basic midamble code number*
-
1
Number of TS
-
3
Number of Hybrid ARQ processes
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..14
Redundancy and constellation version coding sequence
-
{6,5,4,0}
dB
-11.46
Ioc
dBm/
1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.1F.2: Minimum performance requirements for fixed reference measurement channel requirement in multipath channels for category 16-18 UE
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
18
660
9.3.1F.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above for 64QAM modulation.
9.3.1F.4 Method of test
9.3.1F.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.6.
9.3.1F.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [25].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3 tables F.6.3.5.1 and F.6.3.5.2.
9.3.1F.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.1F.3 of test requirement.
Table 9.3.1F.3: Test requirements for fixed reference measurement channel requirement in multipath channels for category 16-18 UE
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
18.6
660
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1G HS-DSCH throughput for Fixed Reference Channels – Categories 19-21 64QAM
9.3.1G.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24], and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 8 and later that support HSDPA UE capability categories 19 - 21.
9.3.1G.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows table specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1G.1: Test parameters for fixed reference measurement channel requirements for category 19-21 UE
Parameters
Unit
Test 1
(Category 19-21)
HS-PDSCH Modulation
-
64QAM
Scrambling code and basic midamble code number*
-
1
Number of TS
-
4
Number of Hybrid ARQ processes
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..14
Redundancy and constellation version coding sequence
-
{6,5,4,0}
dB
-11.46
Ioc
dBm/
1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.1G.2: Minimum performance requirements for fixed reference measurement channel requirement in multipath channels for category 19-21 UE
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
18
875
9.3.1G.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above for 64QAM modulation.
9.3.1G.4 Method of test
9.3.1G.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.6.
9.3.1G.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [25].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3 tables F.6.3.5.1 and F.6.3.5.2.
9.3.1G.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.1G.3 of test requirement.
Table 9.3.1G.3: Test requirements for fixed reference measurement channel requirement in multipath channels for category 19-21 UE
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
18.6
875
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1H HS-DSCH throughput for Fixed Reference Channels – Categories 22-24 64QAM
9.3.1H.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24], and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 8 and later that support HSDPA UE capability categories 16 - 18.
9.3.1H.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows table specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1H.1: Test parameters for fixed reference measurement channel requirements for category 22-24 UE
Parameters
Unit
Test 1
(Category 22-24)
HS-PDSCH Modulation
-
64QAM
Scrambling code and basic midamble code number*
-
1
Number of TS
-
5
Number of Hybrid ARQ processes
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..14
Redundancy and constellation version coding sequence
-
{6,5,4,0}
dB
-11.46
Ioc
dBm/
1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.1H.2: Minimum performance requirements for fixed reference measurement channel requirement in multipath channels for category 22-24 UE
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
18
1090
9.3.1H.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above for 64QAM modulation.
9.3.1H.4 Method of test
9.3.1H.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1A.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.6.
9.3.1H.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [25].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3 tables F.6.3.5.1 and F.6.3.5.2.
9.3.1H.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.1H.3 of test requirement.
The pass / fail decision for throughput is done according to Annex F.6.3.
Table 9.3.1H.3: Test requirements for fixed reference measurement channel requirement in multipath channels for category 22-24 UE
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
18.6
1090
9.3.1I HS-DSCH throughput for Fixed Reference Channels –MIMO UE Category 25
9.3.1I.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and tests for category25 apply to 1,28 Mcps TDD UEs from release 8 and later that MIMO is configured.
If MIMO is not configured, a category 25 UE should have the capability of category 18.
9.3.1I.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows tables specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1I.1: Test parameters for fixed reference measurement channels for Category 25 UE class
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
HS-PDSCH Modulation
-
QPSK
16QAM
Scrambling code and basic midamble code number*
-
0
Number of TS
-
3
Number of Hybrid ARQ processes per stream
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..16
C(i,16)
i=1..16
Redundancy and constellation version coding sequence
-
{0,0,0,0}
{6,2,1,5}
dB
-12.04
-12.04
Stream Number Configuration
-
Fixed Dual Stream
Fixed Single Stream
(2nd Stream is not used)
Fixed Dual Stream
Fixed Single Stream
(2nd Stream is not used)
Ioc
dBm/ 1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.1I.2: Performance requirements for fixed reference channels for Category 25 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10
390
2
PA3
6
160
3
PA3
16
860
4
PA3
12
370
9.3.1I.3 Test purpose
To verify that the MIMO configured UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, for QPSK and 16QAM modulation.
9.3.1I.4 Method of test
9.3.1I.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A..11010a8
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1I.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. (e.g. Fixed reference Channel Definition (16 QAM): The information bit payload block is 3650 bits long. Hence the PRBSequence must be at least 3650 * 10 bits long. ) Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3 tables F.6.3.5.1 and F.6.3.5.2.
9.3.1I.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in tables above of test requirement.
Table 9.3.1I.3: Test requirements for fixed reference channels for Category 25 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10.6
390
2
PA3
6.6
160
3
PA3
16.6
860
4
PA3
12.6
370
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1J HS-DSCH throughput for Fixed Reference Channels –MIMO UE Category 26
9.3.1J.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and tests for category 26 apply to 1,28 Mcps TDD UEs from release 8 and later that MIMO is configured.
If MIMO is not configured, a category 26 UE should have the capability of category 21
9.3.1J.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows tables specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1J.1: Test parameters for fixed reference measurement channels for Category 26 UE class
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
HS-PDSCH Modulation
-
QPSK
16QAM
Scrambling code and basic midamble code number*
-
0
Number of TS
-
4
Number of Hybrid ARQ processes per stream
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..16
C(i,16)
i=1..16
Redundancy and constellation version coding sequence
-
{0,0,0,0}
{6,2,1,5}
dB
-12.04
-12.04
Stream Number Configuration
-
Fixed Dual Stream
Fixed Single Stream
(2nd Stream is not used)
Fixed Dual Stream
Fixed Single Stream
(2nd Stream is not used)
Ioc
dBm/ 1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.1J.2: Performance requirements for fixed reference channels for Category 26 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10
650
2
PA3
6
220
3
PA3
16
950
4
PA3
12
380
9.3.1J.3 Test purpose
To verify that the MIMO configured UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, for QPSK and 16QAM modulation.
9.3.1J.4 Method of test
9.3.1J.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10aA.18
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1J.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3 tables F.6.3.5.1 and F.6.3.5.2.
9.3.1J.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in tables above of test requirement.
Table 9.3.1J.3: Test requirements for fixed reference channels for Category 26 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10.6
650
2
PA3
6.6
220
3
PA3
16.6
950
4
PA3
12.6
380
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1K HS-DSCH throughput for Fixed Reference Channels –MIMO UE Category 27
9.3.1K.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and tests for category 27 apply to 1,28 Mcps TDD UEs from release 8 and later that MIMO is configured.
If MIMO is not configured, a category 27 UE should have the capability of category 24
9.3.1K.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows tables specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1K.1: Test parameters for fixed reference measurement channels for Category 27 UE class
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
HS-PDSCH Modulation
-
QPSK
16QAM
Scrambling code and basic midamble code number*
-
0
Number of TS
-
5
Number of Hybrid ARQ processes per stream
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..16
C(i,16)
i=1..16
Redundancy and constellation version coding sequence
-
{0,0,0,0}
{6,2,1,5}
dB
-12.04
-12.04
Stream Number Configuration
-
Fixed Dual Stream
Fixed Single Stream
(2nd Stream is not used)
Fixed Dual Stream
Fixed Single Stream
(2nd Stream is not used)
Ioc
dBm/ 1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.1K.2: Performance requirements for fixed reference channels for Category 27 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10
850
2
PA3
6
280
3
PA3
16
1200
4
PA3
12
500
9.3.1K.3 Test purpose
To verify that the MIMO configured UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, for QPSK and 16QAM modulation.
9.3.1K.4 Method of test
9.3.1K.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10aA.18
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1K.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3 tables F.6.3.5.1 and F.6.3.5.2.
9.3.1K.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in tables above of test requirement.
Table 9.3.1K.3: Test requirements for fixed reference channels for Category 27 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
10.6
850
2
PA3
6.6
280
3
PA3
16.6
1200
4
PA3
12.6
500
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1L HS-DSCH throughput for Fixed Reference Channels –MIMO UE Category 28
9.3.1L.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and tests for category 28 apply to 1,28 Mcps TDD UEs from release 8 and later that MIMO is configured.
9.3.1L.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows tables specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1L.1: Test parameters for fixed reference measurement channels for Category 28 UE class
Parameters
Unit
Test 1
Test 2
HS-PDSCH Modulation
-
64QAM
Scrambling code and basic midamble code number*
-
0
Number of TS
-
3
Number of Hybrid ARQ processes per stream
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..16
Redundancy and constellation version coding sequence
-
{6,5,4,0}
dB
-12.04
Stream Number Configuration
-
Fixed Dual Stream
Fixed Single Stream
(2nd Stream is not used)
Ioc
dBm/ 1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.1L.2: Performance requirements for fixed reference channels for Category 28 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
20
800
2
PA3
18
540
9.3.1L.3 Test purpose
To verify that the MIMO configured UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, for 64QAM modulation.
9.3.1L.4 Method of test
9.3.1L.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10aA.18
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1L.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3 tables F.6.3.5.1 and F.6.3.5.2.
9.3.1L.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in tables above of test requirement.
Table 9.3.1L.3: Performance requirements for fixed reference channels for Category 28 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
20.6
800
2
PA3
18.6
540
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1M HS-DSCH throughput for Fixed Reference Channels –MIMO UE CategoriesCategory 29
9.3.1M.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and tests for category 29 apply to 1,28 Mcps TDD UEs from release 8 and later that MIMO is configured.
9.3.1M.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows tables specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1M.1: Test parameters for fixed reference measurement channels for Category 29 UE class
Parameters
Unit
Test 1
Test 2
HS-PDSCH Modulation
-
64QAM
Scrambling code and basic midamble code number*
-
0
Number of TS
-
4
Number of Hybrid ARQ processes per stream
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..16
Redundancy and constellation version coding sequence
-
{6,5,4,0}
dB
-12.04
Stream Number Configuration
-
Fixed Dual Stream
Fixed Single Stream
(2nd Stream is not used)
Ioc
dBm/ 1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.1M.2: Performance requirements for fixed reference channels for Category 29 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
20
1200
2
PA3
18
780
9.3.1M.3 Test purpose
To verify that the MIMO configured UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, for 64QAM modulation.
9.3.1M.4 Method of test
9.3.1M.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.18
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1M.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3 tables F.6.3.5.1 and F.6.3.5.2.
9.3.1M.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in tables above of test requirement.
Table 9.3.1M.3: Performance requirements for fixed reference channels for Category 28 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
20.6
1200
2
PA3
18.6
780
The pass / fail decision for throughput is done according to Annex F.6.3.
9.3.1N HS-DSCH throughput for Fixed Reference Channels –MIMO UE CategoriesCategory 30
9.3.1N.1 Definition and applicability
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and tests for category 30 apply to 1,28 Mcps TDD UEs from release 8 and later that MIMO is configured.
9.3.1N.2 Minimum requirements
For the parameters specified in below tables the measured throughput shall be equal to or better than the the specified value in belows tables specified the performance requirement. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.1N.1: Test parameters for fixed reference measurement channels for Category 30 UE class
Parameters
Unit
Test 1
Test 2
HS-PDSCH Modulation
-
64QAM
Scrambling code and basic midamble code number*
-
0
Number of TS
-
5
Number of Hybrid ARQ processes per stream
-
4
Maximum number of Hybrid ARQ transmissions
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
i=1..16
Redundancy and constellation version coding sequence
-
{6,5,4,0}
dB
-12.04
Stream Number Configuration
-
Fixed Dual Stream
Fixed Single Stream
(2nd Stream is not used)
Ioc
dBm/ 1.28MHz
-60
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.1N.2: Performance requirements for fixed reference channels for Category 30 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
20
1570
2
PA3
18
1000
9.3.1N.3 Test purpose
To verify that the MIMO configured UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, for 64QAM modulation.
9.3.1N.4 Method of test
9.3.1N.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.18
2) Set Ack/Nack/ DTX handling at the SS as table 9.3.1.1,Setup fading simulators as fading conditions, which are described in table D.2.2.1.A.
3) Set up a HSDPA connection according to the Generic HSDPA setup procedure. See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
4) Set the test parameters according to above tables of test parameters. The configuration of the downlink channels is defined in table C.4.2.
9.3.1N.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
2) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [26].
3) For all relevant propagation conditions,count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.3 tables F.6.3.5.1 and F.6.3.5.2.
9.3.1N.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in tables above of test requirement.
Table 9.3.1N.3: Performance requirements for fixed reference channels for Category 28 UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
20.6
1570
2
PA3
18.6
1000
The pass / fail decision for throughput is done according to Annex F.6.3.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.2 HS-DSCH throughput for Variable Reference Channels
|
The overall performance metric for HS-DSCH requirements is the throughput “R” measured on HS-DSCH.
9.3.2A HS-DSCH throughput for Variable Reference Channels 0.5 Mbps UE class
9.3.2A.1 Definition and applicability
The HS-DSCH data throughput for variable reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 0.5Mbps UE class.
9.3.2A.2 Minimum requirements
For the parameters specified in tables 9.3.2A.1 the measured throughput shall be equal to or better than the the specified value in table 9.3.2A.2. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.2A.1: Test parameters for variable reference measurement channel requirements for 0.5 Mbps UE class
Parameter
Unit
Test 1
Test 2
Test 3
HS-PDSCH Modulation and TBS
-
*
Scrambling code and basic midamble code Number **
-
1
Midamble
Common midamble
Number of TS****
-
2
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
Redundancy and constellation version coding sequence
Xrv
0
HS-PDSCH Channelization Codes**
C(k,Q)
C(i,16)
1i10
HS-PDSCHi_Ec/Ior
dB
-10
Ioc
dBm
-60
* Note 1 As requested by the last received CQI report
**Note 2 Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
***Note 3 If the indicated CQI is 0, the Node-B emulator shall format the next HS-PDSCH transmission with the transport block size and the modulation scheme that were previously used.
****Note: The timeslot just after the second switch point should be included.
Table 9.3.2A.2: Minimum performance requirements for variable reference measurement channel requirement in multipath channels for 0.5 Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15
242
2
PB3
15
244
3
VA30
15
211
9.3.2A.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined in table 9.3.2A.1, with the selection of QPSK and 16QAM modulation, and appropriate blocksize being determined by the SS based on the CQI reported by the UE.
9.3.2A.4 Method of test
9.3.2A.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Setup fading simulators as fading conditions , which are described in table D.2.2.1.A.
4) Set up a HSDPA connection according to the Generic HSDPA setup procedure,See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
5) Set the test parameters for tests according to above tables of test paramters
6) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [26].
9.3.2A.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63(the first HSDPA block size isn’t recorded),then SS will decode the CQI report and transmit a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.
2) For any HSDPA block transmitted by the SS, record transmitted block size and relevant received ACK, NACK and statDTX reported by UE. If UE reports ACK,the transmitted block is correctly received by UE.Continue transmission of the HS-PDSCH data and record transmitted block size until [2000] records have been reached.
3) For all relevant propagation conditions ,calculate the throughput, which is the ratio of the sum of correctly received transport bits over the testing time. [2000] multiplied by transmission time interval is the testing time.
9.3.2A.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.2A.3 of test requirement.
Table 9.3.2A.3: Test requirements for variable reference measurement channel requirement in multipath channels for 0.5 Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15.6
242
2
PB3
15.6
244
3
VA30
15.6
211
9.3.2B HS-DSCH throughput for Variable Reference Channels 1.1 Mbps UE class
9.3.2B.1 Definition and applicability
The HS-DSCH data throughput for variable reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 1.1Mbps UE class.
9.3.2B.2 Minimum requirements
For the parameters specified in tables 9.3.2B.1 the measured throughput shall be equal to or better than the the specified value in table 9.3.2B.2. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.2B.1: Test parameters for variable reference measurement channel requirements for 1.1 Mbps UE class
Parameter
Unit
Test 1
Test 2
Test 3
HS-PDSCH Modulation and TBS
-
*
Scrambling code and basic midamble code Number **
-
1
Midamble
Common midamble
Number of TS****
-
2
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
Redundancy and constellation version coding sequence
Xrv
0
HS-PDSCH Channelization Codes**
C(k,Q)
C(i,16)
1i10
HS-PDSCHi_Ec/Ior
dB
-10
Ioc
dBm
-60
* Note 1 As requested by the last received CQI report
**Note 2 Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
***Note 3 If the indicated CQI is 0, the Node-B emulator shall format the next HS-PDSCH transmission with the transport block size and the modulation scheme that were previously used.
****Note: The timeslot just after the second switch point should be included.
Table 9.3.2B.2: Minimum performance requirements for variable reference measurement channel requirement in multipath channels for 1.1 Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15
318
2
PB3
15
323
3
VA30
15
213
9.3.2B.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined in table 9.3.2B.1, with the selection of QPSK and 16QAM modulation, and appropriate blocksize being determined by the SS based on the CQI reported by the UE.
9.3.2B.4 Method of test
9.3.2B.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Setup fading simulators as fading conditions , which are described in table D.2.2.1.A.
4) Set up a HSDPA connection according to the Generic HSDPA setup procedure,See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
5) Set the test parameters for tests according to above tables of test paramters
6) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [26].
9.3.2B.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63(the first HSDPA block size isn’t recorded),then SS will decode the CQI report and transmit a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.
2) For any HSDPA block transmitted by the SS, record transmitted block size and relevant received ACK, NACK and statDTX reported by UE. If UE reports ACK,the transmitted block is correctly received by UE.Continue transmission of the HS-PDSCH data and record transmitted block size until [2000] records have been reached.
3) For all relevant propagation conditions ,calculate the throughput, which is the ratio of the sum of correctly received transport bits over the testing time. [2000] multiplied by transmission time interval is the testing time.
9.3.2B.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.2B.3 of testrequirement.
Table 9.3.2B.3: Test requirements for variable reference measurement channel requirement in multipath channels for 1.1 Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15.6
318
2
PB3
15.6
323
3
VA30
15.6
213
9.3.2C HS-DSCH throughput for Variable Reference Channels 1.6 Mbps UE class
9.3.2C.1 Definition and applicability
The HS-DSCH data throughput for variable reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 1.6Mbps UE class.
9.3.2C.2 Minimum requirements
For the parameters specified in tables 9.3.2C.1 the measured throughput shall be equal to or better than the the specified value in table 9.3.2C.2. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.2C.1: Test parameters for variable reference measurement channel requirements for 1.6 Mbps UE class
Parameter
Unit
Test 1
Test 2
Test 3
HS-PDSCH Modulation and TBS
-
*
Scrambling code and basic midamble code Number **
-
1
Midamble
Common midamble
Number of TS****
-
3
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
Redundancy and constellation version coding sequence
Xrv
0
HS-PDSCH Channelization Codes**
C(k,Q)
C(i,16)
1i10
HS-PDSCHi_Ec/Ior
dB
-10
Ioc
dBm
-60
* Note 1 As requested by the last received CQI report
**Note 2 Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
***Note 3 If the indicated CQI is 0, the Node-B emulator shall format the next HS-PDSCH transmission with the transport block size and the modulation scheme that were previously used.
****Note: The timeslot just after the second switch point should be included.
Table 9.3.2C.2: Minimum performance requirements for variable reference measurement channel requirement in multipath channels for 1.6 Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15
480
2
PB3
15
483
3
VA30
15
323
9.3.2C.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined in table 9.3.2C.1, with the selection of QPSK and 16QAM modulation, and appropriate blocksize being determined by the SS based on the CQI reported by the UE.
9.3.2C.4 Method of test
9.3.2C.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Setup fading simulators as fading conditions , which are described in table D.2.2.1.A.
4) Set up a HSDPA connection according to the Generic HSDPA setup procedure,See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
5) Set the test parameters for tests according to above tables of test paramters
6) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [26].
9.3.2C.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63(the first HSDPA block size isn’t recorded),then SS will decode the CQI report and transmit a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.
2) For any HSDPA block transmitted by the SS, record transmitted block size and relevant received ACK, NACK and statDTX reported by UE. If UE reports ACK,the transmitted block is correctly received by UE.Continue transmission of the HS-PDSCH data and record transmitted block size until [2000] records have been reached.
3) For all relevant propagation conditions ,calculate the throughput, which is the ratio of the sum of correctly received transport bits over the testing time. [2000] multiplied by transmission time interval is the testing time.
9.3.2C.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.2C.3 of testrequirement.
Table 9.3.2C.3: Test requirements for variable reference measurement channel requirement in multipath channels for 1.6 Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15.6
480
2
PB3
15.6
483
3
VA30
15.6
323
9.3.2D HS-DSCH throughput for Variable Reference Channels 2.2 Mbps UE class
9.3.2D.1 Definition and applicability
The HS-DSCH data throughput for variable reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 2.2Mbps UE class.
9.3.2D.2 Minimum requirements
For the parameters specified in tables 9.3.2D.1 the measured throughput shall be equal to or better than the the specified value in table 9.3.2D.2. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.2D.1: Test parameters for variable reference measurement channel requirements for 2.2 Mbps UE class
Parameter
Unit
Test 1
Test 2
Test 3
HS-PDSCH Modulation and TBS
-
*
Scrambling code and basic midamble code Number **
-
1
Midamble
Common midamble
Number of TS****
-
4
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
Redundancy and constellation version coding sequence
Xrv
0
HS-PDSCH Channelization Codes**
C(k,Q)
C(i,16)
1i10
HS-PDSCHi_Ec/Ior
dB
-10
Ioc
dBm
-60
* Note 1 As requested by the last received CQI report
**Note 2 Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
***Note 3 If the indicated CQI is 0, the Node-B emulator shall format the next HS-PDSCH transmission with the transport block size and the modulation scheme that were previously used.
****Note: The timeslot just after the second switch point should be included.
Table 9.3.2D.2: Minimum performance requirements for variable reference measurement channel requirement in multipath channels for 2.2 Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15
625
2
PB3
15
631
3
VA30
15
418
9.3.2D.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined in table 9.3.2D.1, with the selection of QPSK and 16QAM modulation, and appropriate blocksize being determined by the SS based on the CQI reported by the UE.
9.3.2D.4 Method of test
9.3.2D.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Setup fading simulators as fading conditions , which are described in table D.2.2.1.A.
4) Set up a HSDPA connection according to the Generic HSDPA setup procedure,See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
5) Set the test parameters for tests according to above tables of test paramters
6) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [26].
9.3.2D.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63(the first HSDPA block size isn’t recorded),then SS will decode the CQI report and transmit a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.
2) For any HSDPA block transmitted by the SS, record transmitted block size and relevant received ACK, NACK and statDTX reported by UE. If UE reports ACK,the transmitted block is correctly received by UE.Continue transmission of the HS-PDSCH data and record transmitted block size until [2000] records have been reached.
3) For all relevant propagation conditions ,calculate the throughput, which is the ratio of the sum of correctly received transport bits over the testing time. [2000] multiplied by transmission time interval is the testing time.
9.3.2D.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.2D.3 of testrequirement.
Table 9.3.2D.3: Test requirements for variable reference measurement channel requirement in multipath channels for 2.2 Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15.6
625
2
PB3
15.6
631
3
VA30
15.6
418
9.3.2E HS-DSCH throughput for Variable Reference Channels 2.8 Mbps UE class
9.3.2E.1 Definition and applicability
The HS-DSCH data throughput for variable reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 2.2Mbps UE class.
9.3.2E.2 Minimum requirements
For the parameters specified in tables 9.3.2E.1 the measured throughput shall be equal to or better than the the specified value in table 9.3.2E.2. The reference for this requirement is TS 25.102 [1] section 9.
Table 9.3.2E.1: Test parameters for variable reference measurement channel requirements for 2.8 Mbps UE class
Parameter
Unit
Test 1
Test 2
Test 3
HS-PDSCH Modulation and TBS
-
*
Scrambling code and basic midamble code Number **
-
1
Midamble
Common midamble
Number of TS
-
5
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
Redundancy and constellation version coding sequence
Xrv
0
HS-PDSCH Channelization Codes**
C(k,Q)
C(i,16)
1i10
HS-PDSCHi_Ec/Ior
dB
-10
Ioc
dBm
-60
* Note 1 As requested by the last received CQI report
**Note 2 Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
***Note 3 If the indicated CQI is 0, the Node-B emulator shall format the next HS-PDSCH transmission with the transport block size and the modulation scheme that were previously used.
Table 9.3.2E.2: Minimum performance requirements for variable reference measurement channel requirement in multipath channels for 2.8 Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15
783
2
PB3
15
792
3
VA30
15
544
9.3.2E.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined in table 9.3.2E.2, with the selection of QPSK and 16QAM modulation, and appropriate blocksize being determined by the SS based on the CQI reported by the UE.
9.3.2E.4 Method of test
9.3.2E.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Setup fading simulators as fading conditions , which are described in table D.2.2.1.A.
4) Set up a HSDPA connection according to the Generic HSDPA setup procedure,See TS 34.108 [3] and TS 34.109 [4] for details regarding generic HSDPA setup procedure.
5) Set the test parameters for tests according to above tables of test paramters
6) The information bit data shall be pseudo random and not repeated not before 10 different information bit payload blocks are processed. Use a PRBS from ITU-R O.153 Ref [26].
9.3.2E.4.2 Procedure
1) Once the HSDPA connection is setup, start transmitting HSDPA Data.
The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63(the first HSDPA block size isn’t recorded),then SS will decode the CQI report and transmit a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.
2) For any HSDPA block transmitted by the SS, record transmitted block size and relevant received ACK, NACK and statDTX reported by UE. If UE reports ACK,the transmitted block is correctly received by UE.Continue transmission of the HS-PDSCH data and record transmitted block size until [2000] records have been reached.
3) For all relevant propagation conditions ,calculate the throughput, which is the ratio of the sum of correctly received transport bits over the testing time. [2000] multiplied by transmission time interval is the testing time.
9.3.2E.5 Test Requirements
Tables of test parameters define the primary level settings including test tolerance for all relevant throughput tests. the measured throughput shall be equal to or better than the the specified value in table 9.3.2E.3 of testrequirement.
Table 9.3.2E.3: Test requirements for variable reference measurement channel requirement in multipath channels for 2.8 Mbps UE class
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
15.6
783
2
PB3
15.6
792
3
VA30
15.6
544
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.3 Reporting of HS-DSCH Channel Quality Indicator
|
9.3.3A Reporting of HS-DSCH Channel Quality Indicator-0.5Mbps UE class
9.3.3A.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 0.5 Mbps UE class.
9.3.3A.2 Minimum requirements
For the parameters specified in tables 9.3.3.1 the UE shall report a CQI value within the limits of table 9.3.3A.2.
Table 9.3.3A.1: Test parameters for CQI reporting measurement channel requirements for 0.5Mbps UE class
0.5Mbps UE
Parameter
Unit
Test 1
Number of TS
-
2
Number of HS-PDSCH codes per TS
-
10
HS-PDSCHi_Ec/Ior
dB
-10
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
1i10
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
dB
1
Table 9.3.3A.2 Performance requirements for CQI reporting measurement channel requirements for 0.5Mbps UE class
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 3
90
10%
9.3.3A.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, such that CQI reported by the UE falls within the acceptable range.
9.3.3A.4 Method of test
9.3.3A.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS and an AWGN source to the UE antenna connector as shown in figure A.9.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Set up a call according to the Generic call setup procedure.
See TS 34.108 [3] and TS 34.109 [4] for details regarding generic call setup procedure.
Note: The following value of x is derived from Table 9.3.3A.2
9.3.3A.4.2 Procedure
1) Set test conditions according to test 1 according table 9.3.3A.1.
Note: the following part of the procedure will test, if the UE reports a limited range of CQI indicator under the predefined channel conditions.
2) The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63,then SS will decodes the CQI report and transmits a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.For any HSDPA block transmitted by the SS, record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of the HS-PDSCH data and collect RTBS value of CQI until [2000] reports have been gathered.
3) Set up a relative frequency distribution for the RTBS value of CQI indicator reported. Calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side). This RTBS value of CQI indicator is declared as Median CQI value,
4) If [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI - x) ≤ Median CQI ≤ ( Median CQI + x) then continue with next step , otherwise fail the UE.
5) Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
9.3.3A.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3A.4.2.
No test tolerance is applied to the test parameters.
9.3.3B Reporting of HS-DSCH Channel Quality Indicator-1.1Mbps UE class
9.3.3B.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 1.1 Mbps UE class..
9.3.3B.2 Minimum requirements
For the parameters specified in tables 9.3.3B.1 the UE shall report a CQI value within the limits of table 9.3.3B.2.
Table 9.3.3B.1: Test parameters for CQI reporting measurement channel requirements for 1.1Mbps UE class
1.1Mbps UE
Parameter
Unit
Test 1
Test 2
Number of TS
-
2
Number of HS-PDSCH codes per TS
-
10
HS-PDSCHi_Ec/Ior
dB
-10
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
1i10
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
dB
1
8
Table 9.3.3B.2 Performance requirements for CQI reporting measurement channel requirements for 1.1Mbps U E class
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 3
90
10%
Test 2
+/- 2
90
9.3.3B.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, such that CQI reported by the UE falls within the acceptable range.
9.3.3B.4 Method of test
9.3.3B.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS and an AWGN source to the UE antenna connector as shown in figure A.9.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Set up a call according to the Generic call setup procedure.
See TS 34.108 [3] and TS 34.109 [4] for details regarding generic call setup procedure.
Note: The following value of x is derived from Table 9.3.3B.2
9.3.3B.4.2 Procedure
1) Set test conditions according to test 1 according table 9.3.3B.1.
Note: the following part of the procedure will test, if the UE reports a limited range of CQI indicator under the predefined channel conditions.
2) The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63,then SS will decodes the CQI report and transmits a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.For any HSDPA block transmitted by the SS, record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of the HS-PDSCH data and collect RTBS value of CQI until [2000] reports have been gathered.
3) Set up a relative frequency distribution for the RTBS value of CQI indicator reported. Calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side). This RTBS value of CQI indicator is declared as Median CQI value,
4) If [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI - x) ≤ Median CQI ≤ ( Median CQI + x) then continue with next step , otherwise fail the UE.
5) Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
6) Repeat the same procedure (steps 2 to 5) with test conditions according to the table 9.3.3B.1.
9.3.3B.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3B.4.2.
No test tolerance is applied to the test parameters.
9.3.3C Reporting of HS-DSCH Channel Quality Indicator-1.6Mbps UE class
9.3.3C.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 1.6 Mbps UE class..
9.3.3C.2 Minimum requirements
For the parameters specified in tables 9.3.3C.1 the UE shall report a CQI value within the limits of table 9.3.3C.2.
Table 9.3.3C.1: Test parameters for CQI reporting measurement channel requirements for 1.6Mbps UE class
1.6Mbps UE
Parameter
Unit
Test 1
Test 2
Number of TS
-
3
Number of HS-PDSCH codes per TS
-
10
HS-PDSCHi_Ec/Ior
dB
-10
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
1i10
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
dB
1
8
Table 9.3.3C.2 Performance requirements for CQI reporting measurement channel requirements for 1.6Mbps U E class
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
Test 2
+/- 2
90
9.3.3C.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, such that CQI reported by the UE falls within the acceptable range.
9.3.3C.4 Method of test
9.3.3C.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS and an AWGN source to the UE antenna connector as shown in figure A.9.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Set up a call according to the Generic call setup procedure.
See TS 34.108 [3] and TS 34.109 [4] for details regarding generic call setup procedure.
Note: The following value of x is derived from Table 9.3.3C.2
9.3.3C.4.2 Procedure
1) Set test conditions according to test 1 according table 9.3.3C.1.
Note: the following part of the procedure will test, if the UE reports a limited range of CQI indicator under the predefined channel conditions.
2) The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63,then SS will decodes the CQI report and transmits a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.For any HSDPA block transmitted by the SS, record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of the HS-PDSCH data and collect RTBS value of CQI until [2000] reports have been gathered.
3) Set up a relative frequency distribution for the RTBS value of CQI indicator reported. Calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side). This RTBS value of CQI indicator is declared as Median CQI value,
4) If [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI - x) ≤ Median CQI ≤ ( Median CQI + x) then continue with next step , otherwise fail the UE.
5) Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
6) Repeat the same procedure (steps 2 to 5) with test conditions according to the table 9.3.3C.1.
9.3.3C.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3C.4.2.
No test tolerance is applied to the test parameters.
9.3.3D Reporting of HS-DSCH Channel Quality Indicator-2.2Mbps UE class
9.3.3D.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 2.2 Mbps UE class..
9.3.3D.2 Minimum requirements
For the parameters specified in tables 9.3.3D.1 the UE shall report a CQI value within the limits of table 9.3.3D.2.
Table 9.3.3D.1: Test parameters for CQI reporting measurement channel requirements for 2.2Mbps UE class
1.6Mbps UE
Parameter
Unit
Test 1
Test 2
Number of TS
-
4
Number of HS-PDSCH codes per TS
-
10
HS-PDSCHi_Ec/Ior
dB
-10
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
1i10
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
dB
1
8
Table 9.3.3D.2 Performance requirements for CQI reporting measurement channel requirements for 2.2Mbps U E class
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
Test 2
+/- 2
90
9.3.3D.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, such that CQI reported by the UE falls within the acceptable range.
9.3.3D.4 Method of test
9.3.3D.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS and an AWGN source to the UE antenna connector as shown in figure A.9.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Set up a call according to the Generic call setup procedure.
See TS 34.108 [3] and TS 34.109 [4] for details regarding generic call setup procedure.
Note: The following value of x is derived from Table 9.3.3D.2
9.3.3D.4.2 Procedure
1) Set test conditions according to test 1 according table 9.3.3D.1.
Note: the following part of the procedure will test, if the UE reports a limited range of CQI indicator under the predefined channel conditions.
2) The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63,then SS will decodes the CQI report and transmits a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.For any HSDPA block transmitted by the SS, record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of the HS-PDSCH data and collect RTBS value of CQI until [2000] reports have been gathered.
3) Set up a relative frequency distribution for the RTBS value of CQI indicator reported. Calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side). This RTBS value of CQI indicator is declared as Median CQI value,
4) If [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI - x) ≤ Median CQI ≤ ( Median CQI + x) then continue with next step , otherwise fail the UE.
5) Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
6) Repeat the same procedure (steps 2 to 5) with test conditions according to the table 9.3.3D.1.
9.3.3D.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3D.4.2.
No test tolerance is applied to the test parameters.
9.3.3E Reporting of HS-DSCH Channel Quality Indicator-2.8Mbps UE class
9.3.3E.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA which is 2.8 Mbps UE class..
9.3.3E.2 Minimum requirements
For the parameters specified in tables 9.3.3E.1 the UE shall report a CQI value within the limits of table 9.3.3E.2.
Table 9.3.3E.1: Test parameters for CQI reporting measurement channel requirements for 2.8Mbps UE class
2.2Mbps UE
Parameter
Unit
Test 1
Test 2
Number of TS
-
5
Number of HS-PDSCH codes per TS
-
10
HS-PDSCHi_Ec/Ior
dB
-10
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
1i10
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
dB
1
8
Table 9.3.3E.2 Performance requirements for CQI reporting measurement channel requirements for 2.8Mbps U E class
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
Test 2
+/- 2
90
9.3.3E.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, such that CQI reported by the UE falls within the acceptable range.
9.3.3E.4 Method of test
9.3.3E.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS and an AWGN source to the UE antenna connector as shown in figure A.9.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Set up a call according to the Generic call setup procedure.
See TS 34.108 [3] and TS 34.109 [4] for details regarding generic call setup procedure.
Note: The following value of x is derived from Table 9.3.3E.2
9.3.3E.4.2 Procedure
1) Set test conditions according to test 1 according table 9.3.3E.1.
Note: the following part of the procedure will test, if the UE reports a limited range of CQI indicator under the predefined channel conditions.
2) The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63,then SS will decodes the CQI report and transmits a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.For any HSDPA block transmitted by the SS, record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of the HS-PDSCH data and collect RTBS value of CQI until [2000] reports have been gathered.
3) Set up a relative frequency distribution for the RTBS value of CQI indicator reported. Calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side). This RTBS value of CQI indicator is declared as Median CQI value,
4) If [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI - x) ≤ Median CQI ≤ ( Median CQI + x) then continue with next step , otherwise fail the UE.
5) Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
6) Repeat the same procedure (steps 2 to 5) with test conditions according to the table 9.3.3E.1.
9.3.3E.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3E.4.2.
No test tolerance is applied to the test parameters.
9.3.3F Reporting of HS-DSCH Channel Quality Indicator – 64QAM UE capability categories 16 - 18
9.3.3F.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 8 and later that support HSDPA UE capability categories 16 - 18.
9.3.3F.2 Minimum requirements
For the parameters specified in tables 9.3.3A.1 the UE shall report a CQI value within the limits of table 9.3.3F.2.
Table 9.3.3F.1: Test parameters for CQI reporting measurement channel requirements for UE capability categories 16 - 18
Category
16-18
Parameter
Unit
Test 1
Number of TS
-
3
Number of HS-PDSCH codes per TS
-
14
HS-PDSCHi_Ec/Ior
dB
-11.46
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
1i14
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
Ioc**
dBm/1.28MHz
-60
dB
18
Propagation
Channel
-
AWGN
*Note 1: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
**Note 2: For multi-carrier reception, it refers to on each carrier.
Table 9.3.3F.2: Performance requirements for CQI reporting measurement channel requirements for UE capability categories 16 - 18
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
9.3.3F.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, such that CQI reported by the UE falls within the acceptable range.
9.3.3F.4 Method of test
9.3.3F.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, and an AWGN source to the UE antenna connector as shown in figure A.9.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Set up a call according to the Generic call setup procedure.
See TS 34.108 [3] and TS 34.109 [4] for details regarding generic call setup procedure.
NOTE: The following value of x is derived from Table 9.3.3F.2
9.3.3F.4.2 Procedure
1) Set test conditions according to test 1 according table 9.3.3F.1.
NOTE: the following part of the procedure will test, if the UE reports a limited range of CQI indicator under the predefined channel conditions.
2) The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63,then SS will decodes the CQI report and transmits a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.For any HSDPA block transmitted by the SS, record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of the HS-PDSCH data and collect RTBS value of CQI until [2000] reports have been gathered.
3) Set up a relative frequency distribution for the RTBS value of CQI indicator reported. Calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side). This RTBS value of CQI indicator is declared as Median CQI value,
4) If [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI - x) ≤ Median CQI ≤ ( Median CQI + x) then continue with next step , otherwise fail the UE.
5) Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
9.3.3F.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3F.4.2.
No test tolerance is applied to the test parameters.
9.3.3G Reporting of HS-DSCH Channel Quality Indicator – 64QAM UE capability categories 19 - 21
9.3.3G.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 8 and later that support HSDPA UE capability categories 19 - 21.
9.3.3G.2 Minimum requirements
For the parameters specified in tables 9.3.3G.1 the UE shall report a CQI value within the limits of table 9.3.3G.2.
Table 9.3.3G.1: Test parameters for CQI reporting measurement channel requirements for UE capability categories 19 - 21
Category
19-21
Parameter
Unit
Test 1
Number of TS
-
4
Number of HS-PDSCH codes per TS
-
14
HS-PDSCHi_Ec/Ior
dB
-11.46
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
1i14
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
Ioc**
dBm/1.28MHz
-60
dB
18
Propagation
Channel
-
AWGN
*Note 1: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
**Note 2: For multi-carrier reception, it refers to on each carrier.
Table 9.3.3G.2: Performance requirements for CQI reporting measurement channel requirements for UE capability categories 19 - 21
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
9.3.3G.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, such that CQI reported by the UE falls within the acceptable range.
9.3.3G.4 Method of test
9.3.3G.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, and an AWGN source to the UE antenna connector as shown in figure A.9.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Set up a call according to the Generic call setup procedure.
See TS 34.108 [3] and TS 34.109 [4] for details regarding generic call setup procedure.
NOTE: The following value of x is derived from Table 9.3.3G.2
9.3.3G.4.2 Procedure
1) Set test conditions according to test 1 according table 9.3.3G.1.
NOTE: the following part of the procedure will test, if the UE reports a limited range of CQI indicator under the predefined channel conditions.
2) The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63,then SS will decodes the CQI report and transmits a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.For any HSDPA block transmitted by the SS, record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of the HS-PDSCH data and collect RTBS value of CQI until [2000] reports have been gathered.
3) Set up a relative frequency distribution for the RTBS value of CQI indicator reported. Calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side). This RTBS value of CQI indicator is declared as Median CQI value,
4) If [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI - x) ≤ Median CQI ≤ ( Median CQI + x) then continue with next step , otherwise fail the UE.
5) Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
9.3.3G.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3G.4.2.
No test tolerance is applied to the test parameters.
9.3.3H Reporting of HS-DSCH Channel Quality Indicator – 64QAM UE capability categories 22 - 24
9.3.3H.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [1], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 8 and later that support HSDPA UE capability categories 22 - 24.
9.3.3H.2 Minimum requirements
For the parameters specified in tables 9.3.3H.1 the UE shall report a CQI value within the limits of table 9.3.3H.2.
Table 9.3.3H.1: Test parameters for CQI reporting measurement channel requirements for UE capability categories 22 - 24
Category
22-24
Parameter
Unit
Test 1
Number of TS
-
5
Number of HS-PDSCH codes per TS
-
14
HS-PDSCHi_Ec/Ior
dB
-11.46
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,16)
1i14
Number of DPCHo
-
0
Number of HARQ Process
-
4
Number of transmission
-
1
Ioc**
dBm/1.28MHz
-60
dB
18
Propagation
Channel
-
AWGN
*Note 1: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
**Note 2: For multi-carrier reception, it refers to on each carrier.
Table 9.3.3H.2: Performance requirements for CQI reporting measurement channel requirements for UE capability categories 22 - 24
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
9.3.3H.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, such that CQI reported by the UE falls within the acceptable range.
9.3.3H.4 Method of test
9.3.3H.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, and an AWGN source to the UE antenna connector as shown in figure A.9.
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Set up a call according to the Generic call setup procedure.
See TS 34.108 [3] and TS 34.109 [4] for details regarding generic call setup procedure.
NOTE: The following value of x is derived from Table 9.3.3H.2
9.3.3H.4.2 Procedure
1) Set test conditions according to test 1 according table 9.3.3H.1.
NOTE: the following part of the procedure will test, if the UE reports a limited range of CQI indicator under the predefined channel conditions.
2) The SS shall transmit a HSDPA block to UE selecting any TBS value excluding 0 or 63,then SS will decodes the CQI report and transmits a new block on the HS-DSCH with the transport block size and modulation scheme recommended by the UE.For any HSDPA block transmitted by the SS, record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of the HS-PDSCH data and collect RTBS value of CQI until [2000] reports have been gathered.
3) Set up a relative frequency distribution for the RTBS value of CQI indicator reported. Calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side). This RTBS value of CQI indicator is declared as Median CQI value,
4) If [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI - x) ≤ Median CQI ≤ ( Median CQI + x) then continue with next step , otherwise fail the UE.
5) Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
9.3.3H.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3H.4.2.
No test tolerance is applied to the test parameters.
9.3.3I Reporting of HS-DSCH Channel Quality Indicator – category 25 MIMO
9.3.3I.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN and static orthogonal environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [21], section 9.
The requirements and this test apply to 1,28 Mcps TDD MIMO capable UEs category 25 from release 8 and later.
9.3.3I.2 Minimum requirements
For the parameters specified in tables 9.3.3I.1 the UE categories 25 shall report a CQI value within the limits of table 9.3.3I.2.
The MIMO dual stream static orthogonal propagation conditions are defined in Annex D.2.5.1. For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 in dual stream transmission, and the HS-PDSCHi_Ec/Ior should be 0dB.
Table 9.3.3I.1: Test parameters for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Category 25
Parameter
Unit
Test 1
Test 2
Number of TS
-
3
Number of HS-PDSCH codes per TS
-
16
Number of HS-PDSCH codes per TS
-
16
HS-PDSCHi_Ec/Ior
dB
-12.04
HS-PDSCH Channelization Codes
C(k,Q)
C(i,16)
1i16
Number of DPCHo
-
0
Number of HARQ Process per stream
-
4
Number of transmission
-
1
Ioc
dBm
-60
dB
8
10
Stream Number
configuration
-
Single
Stream
Dual
Stream
Propagation Channel
-
AWGN
Static Orthogonal
Table 9.3.3I.2: Performance requirements for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
Test 2
+/- 2
90
9.3.3I.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above, such that CQI reported by the UE falls within the acceptable range.
9.3.3I.4 Method of test
9.3.3I.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.18
2) Set Ack/Nack/DTX handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent each time, this is because HARQ transmissions are set to one, i.e. no re-transmission of failed blocks.
3) Set up a call according to the Generic call setup procedure.
See TS 34.108 [3] and TS 34.109 [4] for details regarding generic call setup procedure.
9.3.3I.4.2 Procedure
For test 1, the test procedure is as followed:
1) Set test conditions according to test 1 according table 9.3.3I.1.
2) The SS shall transmit a HSDPA block on one antenna to UE, selecting any TBS value excluding 0 or 63, then SS will decodes CQI report and transmits a new block on HS-DSCH with the transport block size and modulation scheme recommended by the UE on the other antenna. For any HSDPA block transmitted by the SS, record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of the HS-PDSCH data and collect RTBS value of CQI until [2000] reports have been gathered.
3) Set up a relative frequency distribution for the RTBS value of CQI indicator reported. Calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side) . This RTBS value of CQI indicator is declared as Median CQI value,
4) If [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI - x) ≤ Median CQI ≤ ( Median CQI + x) then continue with next step , otherwise fail the UE.
5) Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
For test 2, the test procedure is as followed:
1) Set test conditions according to test 1 according table 9.3.3I.1.
2) The SS shall transmit two streams on each antenna to UE, each with a sequence of HSDPA blocks. For each stream, SS firstly transmit a HSDPA block, selecting any TBS value excluding 0 or 63, then SS will decodes CQI report and transmits a new block on HS-DSCH with the transport block size and modulation scheme recommended by the UE. For any HSDPA block transmition, the SS shall record the received RTBS value of CQI indicator and the ACK, NACK and statDTX . Continue transmission of each streams of HS-PDSCH data and collect RTBS value of CQI until [2000] reports for this stream have been gathered.
3) For each stream, the SS set up a relative frequency distribution for the RTBS value of CQI indicator reported, then calculate the median value (Median RTBS is the RTBS that is at or crosses 50% distribution from the lower RTBS side) for this stream. This RTBS value of CQI indicator is declared as Median CQI-stream value,
4) For each stream, if [1800] or more of the RTBS value of CQI indicator are in the range (Median CQI-stream - x) ≤ Median CQI-stream ≤ ( Median CQI-stream + x) then continue with next step , otherwise fail the UE.
5) For each stream, Calculate the the ratio ( NACK + statDTX / ACK + NACK + statDTX) when the SS transmit the TBS according to the median-CQI-stream value.If the ratio< 0.1 ,then pass the UE,otherwise fail the UE.
9.3.3I.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3I.4.2.
No test tolerance is applied to the test parameters.
9.3.3J Reporting of HS-DSCH Channel Quality Indicator – category 26 MIMO
9.3.3J.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN and static orthogonal environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [21], section 9.
The requirements and this test apply to 1,28 Mcps TDD MIMO capable UEs category 26 from release 8 and later.
9.3.3J.2 Minimum requirements
For the parameters specified in tables 9.3.3J.1 the UE categories 26 shall report a CQI value within the limits of table 9.3.3J.2.
The MIMO dual stream static orthogonal propagation conditions are defined in Annex D.2.5.1. For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 in dual stream transmission, and the HS-PDSCHi_Ec/Ior should be 0dB.
Table 9.3.3J.1: Test parameters for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Category 26
Parameter
Unit
Test 1
Test 2
Number of TS
-
4
Number of HS-PDSCH codes per TS
-
16
Number of HS-PDSCH codes per TS
-
16
HS-PDSCHi_Ec/Ior
dB
-12.04
HS-PDSCH Channelization Codes
C(k,Q)
C(i,16)
1i16
Number of DPCHo
-
0
Number of HARQ Process per stream
-
4
Number of transmission
-
1
Ioc
dBm
-60
dB
8
10
Stream Number
configuration
-
Single
Stream
Dual
Stream
Propagation Channel
-
AWGN
Static Orthogonal
Table 9.3.3J.2: Performance requirements for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
Test 2
+/- 2
90
9.3.3J.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above, such that CQI reported by the UE falls within the acceptable range.
9.3.3J.4 Method of test
9.3.3J.4.1 Initial conditions
<FFS> According to 9.3.3I
9.3.3J.4.2 Procedure
<FFS> According to 9.3.3I
9.3.3J.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3J.4.2.
No test tolerance is applied to the test parameters.
9.3.3K Reporting of HS-DSCH Channel Quality Indicator – category 27 MIMO
9.3.3K.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN and static orthogonal environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [21], section 9.
The requirements and this test apply to 1,28 Mcps TDD MIMO capable UEs category 27 from release 8 and later.
9.3.3K.2 Minimum requirements
For the parameters specified in tables 9.3.3K.1 the UE categories 27 shall report a CQI value within the limits of table 9.3.3K.2.
The MIMO dual stream static orthogonal propagation conditions are defined in Annex D.2.5.1. For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 in dual stream transmission, and the HS-PDSCHi_Ec/Ior should be 0dB.
Table 9.3.3K.1: Test parameters for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Category 27
Parameter
Unit
Test 1
Test 2
Number of TS
-
5
Number of HS-PDSCH codes per TS
-
16
Number of HS-PDSCH codes per TS
-
16
HS-PDSCHi_Ec/Ior
dB
-12.04
HS-PDSCH Channelization Codes
C(k,Q)
C(i,16)
1i16
Number of DPCHo
-
0
Number of HARQ Process per stream
-
4
Number of transmission
-
1
Ioc
dBm
-60
dB
8
10
Stream Number
configuration
-
Single
Stream
Dual
Stream
Propagation Channel
-
AWGN
Static Orthogonal
Table 9.3.3K.2: Performance requirements for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/-2
90
10%
Test 2
+/-2
90
9.3.3K.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above, such that CQI reported by the UE falls within the acceptable range.
9.3.3K.4 Method of test
9.3.3K.4.1 Initial conditions
<FFS> According to 9.3.3I
9.3.3K.4.2 Procedure
<FFS> According to 9.3.3I
9.3.3K.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3K.4.2.
No test tolerance is applied to the test parameters.
9.3.3L Reporting of HS-DSCH Channel Quality Indicator – category 28 MIMO
9.3.3L.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN and static orthogonal environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [21], section 9.
The requirements and this test apply to 1,28 Mcps TDD MIMO capable UEs category 28 from release 8 and later.
9.3.3L.2 Minimum requirements
For the parameters specified in tables 9.3.3L.1 the UE categories 28 shall report a CQI value within the limits of table 9.3.3L.2.
The MIMO dual stream static orthogonal propagation conditions are defined in Annex D.2.5.1. For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 in dual stream transmission, and the HS-PDSCHi_Ec/Ior should be 0dB.
Table 9.3.3L.1: Test parameters for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Category 28
Parameter
Unit
Test 1
Test 2
Number of TS
-
3
Number of HS-PDSCH codes per TS
-
16
Number of HS-PDSCH codes per TS
-
16
HS-PDSCHi_Ec/Ior
dB
-12.04
HS-PDSCH Channelization Codes
C(k,Q)
C(i,16)
1i16
Number of DPCHo
-
0
Number of HARQ Process per stream
-
4
Number of transmission
-
1
Ioc
dBm
-60
dB
16
18
Stream Number
-
Single
Stream
Dual
Stream
Propagation Channel
-
AWGN
Static Orthogonal
Table 9.3.3L.2: Performance requirements for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
Test 2
+/- 2
90
9.3.3L.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above, such that CQI reported by the UE falls within the acceptable range.
9.3.3L.4 Method of test
9.3.3L.4.1 Initial conditions
<FFS> According to 9.3.3I
9.3.3L.4.2 Procedure
<FFS> According to 9.3.3I
9.3.3L.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3L.4.2.
No test tolerance is applied to the test parameters.
9.3.3M Reporting of HS-DSCH Channel Quality Indicator – category 29 MIMO
9.3.3M.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN and static orthogonal environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [21], section 9.
The requirements and this test apply to 1,28 Mcps TDD MIMO capable UEs category 29 from release 8 and later.
9.3.3M.2 Minimum requirements
For the parameters specified in tables 9.3.3M.1 the UE categories 29 shall report a CQI value within the limits of table 9.3.3M.2.
The MIMO dual stream static orthogonal propagation conditions are defined in Annex D.2.5.1. For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 in dual stream transmission, and the HS-PDSCHi_Ec/Ior should be 0dB.
Table 9.3.3M.1: Test parameters for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Category 29
Parameter
Unit
Test 1
Test 2
Number of TS
-
4
Number of HS-PDSCH codes per TS
-
16
Number of HS-PDSCH codes per TS
-
16
HS-PDSCHi_Ec/Ior
dB
-12.04
HS-PDSCH Channelization Codes
C(k,Q)
C(i,16)
1i16
Number of DPCHo
-
0
Number of HARQ Process per stream
-
4
Number of transmission
-
1
Ioc
dBm
-60
dB
16
18
Stream Number
-
Single
Stream
Dual
Stream
Propagation Channel
-
AWGN
Static Orthogonal
Table 9.3.3M.2: Performance requirements for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
Test 2
+/- 2
90
9.3.3M.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above, such that CQI reported by the UE falls within the acceptable range.
9.3.3M.4 Method of test
9.3.3M.4.1 Initial conditions
<FFS> According to 9.3.3I
9.3.3M.4.2 Procedure
<FFS> According to 9.3.3I
9.3.3M.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3M.4.2.
No test tolerance is applied to the test parameters.
9.3.3N Reporting of HS-DSCH Channel Quality Indicator – category 30 MIMO
9.3.3N.1 Definition and applicability
The reporting accuracy of channel quality indicator (CQI) under AWGN and static orthogonal environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median. The CQI is measured while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [21], section 9.
The requirements and this test apply to 1,28 Mcps TDD MIMO capable UEs category 30 from release 8 and later.
9.3.3N.2 Minimum requirements
For the parameters specified in tables 9.3.3L.1 the UE categories 30 shall report a CQI value within the limits of table 9.3.3L.2.
The MIMO dual stream static orthogonal propagation conditions are defined in Annex D.2.5.1. For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 in dual stream transmission, and the HS-PDSCHi_Ec/Ior should be 0dB.
Table 9.3.3N.1: Test parameters for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Category 30
Parameter
Unit
Test 1
Test 2
Number of TS
-
5
Number of HS-PDSCH codes per TS
-
16
Number of HS-PDSCH codes per TS
-
16
HS-PDSCHi_Ec/Ior
dB
-12.04
HS-PDSCH Channelization Codes
C(k,Q)
C(i,16)
1i16
Number of DPCHo
-
0
Number of HARQ Process per stream
-
4
Number of transmission
-
1
Ioc
dBm
-60
dB
16
18
Stream Number
-
Single
Stream
Dual
Stream
Propagation Channel
-
AWGN
Static Orthogonal
Table 9.3.3N.2: Performance requirements for CQI reporting measurement channel requirements (1.28 Mcps TDD Option)
Test
Permitted CQI range from median (x)
% of time that CQI must be within +/- x of median (Y)
Maximum BLER for median reported CQI
Test 1
+/- 2
90
10%
Test 2
+/- 2
90
9.3.3N.3 Test purpose
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined above, such that CQI reported by the UE falls within the acceptable range.
9.3.3N.4 Method of test
9.3.3N.4.1 Initial conditions
<FFS> According to 9.3.3I
9.3.3N.4.2 Procedure
<FFS> According to 9.3.3I
9.3.3N.5 Test Requirements
The pass fail decision as specified in the test procedure in 9.3.3N.4.2.
No test tolerance is applied to the test parameters.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.4 HS-SCCH Detection Performance
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.4.1 Definition and applicability
|
The detection performance of the HS-SCCH is determined by the probability of event Em, which is declared when the UE is signaled on HS-SCCH, but DTX is observed in the corresponding HS-SICH ACK/NACK field. The probability of event Em is denoted P(Em).
This corresponds to case when the SS indicates to the UE via the HS-SCCH that HSDPA data is to be sent, but the UE fails to decode this correctly.
The normative reference for this test is 25.102 [2], section 9.
The requirements and this test apply to 1,28 Mcps TDD UE from release 5 and later that support HSDPA.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.4.2 Minimum requirements
|
For the parameters specified in tables 9.3.4.1, for each value of HS-SCCH specified in Table 9.3.4.3 the measured P(Em) shall be less than or equal to the corresponding specified value of P(Em). The reference for this requirement is TS 25.102 [1] section 9.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.4.3 Test purpose
|
To verify that the UE receiver is capable meeting the minimum requirements for support of HSDPA in the conditions defined below, and does not report a DTX when valid data was sent, more often than the performance limits allow.
Table 9.3.4.1: Test parameters for HS-SCCH detection (1.28Mcps TDD option)
Parameter
Unit
Test 1
Test2
Number of TS under test
-
1
Number of HS-SCCH codes per timeslot
-
8 (4 x2)
Scrambling code and basic midamble code number*
-
0
Midamble
Common midamble
Number of DPCHo
-
2
Number of H-ARQ process
-
4
HS-SCCH UE Identity
(,, …, )
-
UE1 = 0000000000000000
(UE1 under test)
UE2 = 0101010101010101
UE3 = 1010101010101010
UE4 = 1111111111111111
HS-SCCH Channelization Codes*
C(k,Q)
C(i,16)
1i8
HS-SCCH Channelization Codes for UE under test
C(k,Q)
C(i,16)
1i2
DPCHo Channelization Codes
C(k,Q)
C(i,16)
9i10
dB
-10
Ioc
dBm/1.28MHz
-60
Note *: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 9.3.4.2: Test parameters for HS-PDSCH (1.28Mcps TDD option)
Parameter
Unit
Test 1
Test2
Number of TS under test
-
2
Number of HS-PDSCH codes per timeslot
-
10
Scrambling code and basic midamble code number*
-
0
HS-PDSCH Channelization Codes for UE under test
C(k,Q)
C(i,16)
1i10
dB
-10
Ioc
dBm/1.28MHz
-60
dB
**
Note *: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Note **: Allocate a sufficient power to so that probability of missing HS-DPSCH is very low.
Table 9.3.4.3: Minimum requirement for HS-SCCH detection (1.28Mcps TDD option)
Test Number
Propagation Conditions
(dB)
1
PA3
16
0.01
2
VA30
12
0.01
The propagation conditions are described in Annex D.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.4.4 Method of test
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.4.4.1 Initial conditions
|
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack handling at the SS as table 9.3.1.1 (Fixed channel test)
3) Set up test parameter according to table 9.3.4.1 and able 9.3.4.2.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.4.4.2 Procedure
|
1. The UE is switched on.
2. An RRC connection is set-up according to the generic HSDPA set-up procedure specified in TS 34.108 [3].
3. Count the number of NACK, ACK and statDTX on the UL HS-SICH during the test interval and decide pass or fail according to Annex F.6.1 and table F.6.1.8. NACK and ACK are counted as a pass and statDTX is counted as a failure.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.3.4.5 Test Requirements
|
The probability of event Em denoted as P(Em) (test procedure step 3) shall not exceed the specified value in table 9.3.4.4.
Table 9.3.4.4: Test requirement for HS-SCCH detection (1.28Mcps TDD option)
Test Number
Propagation Conditions
(dB)
1
PA3
16.6
0.01
2
VA30
12.6
0.01
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.4 Performance requirement for 7.68 Mcps TDD option
|
During the Fixed Reference Channel tests the behaviour of the Node-B emulator in response to the ACK/NACK signalling field of the HS-DPCCH is specified in Table 9.4.1:
Table 9.4.1: Node-B Emulator Behaviour in response to ACK/NACK/DTX
HS-DPCCH ACK/NACK Field State
Node-B Emulator Behaviour
ACK
ACK: new transmission using 1st redundancy and constellation version (RV)
NACK
NACK: retransmission using the next RV (up to the maximum permitted number or RV’s)
DTX
DTX: retransmission using the RV previously transmitted to the same H-ARQ process
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.4.1 HS-DSCH throughput for Fixed Reference Channels
| |
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.4.1.1 Definition and applicability
|
The HS-DSCH data throughput for fixed reference channels is defined by the capabilities of the UE as defined in [24] , and the throughput is measured by counting the amount of data succeesfully received at the UE by monitoring the ACK/NACK signalling field of the HS-SICH received at the SS, while random data is streamed from the SS to the UE.
The normative reference for this test is 25.102 [2], section 9.3.
The requirements and this test apply to 7.68 Mcps TDD UE from release 7 and later that support HSDPA.
|
40bd05ebf1e9d686c3dc55dd3e817398
|
34.122
|
9.4.1.2 Minimum requirements
|
The requirements are specified in terms of minimum information bit throughput R for the DL reference channels specified in Annex C.4.2A with the addition of the relevant parameters in Tables 9.4.1.1 and 9.4.1.3.
Using this configuration the throughput shall meet or exceed the minimum requirements specified in tables 9.4.1.2 and 9.4.1.4.
Table 9.4.1.1: Test parameters for fixed reference measurement channel requirements for 5,3 Mbps – Category 8 - UE (7,68 Mcps TDD Option) QPSK
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
HS-PDSCH Modulation
-
QPSK
Scrambling code and basic midamble code number*
-
0, 1
Number of TS
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,32)
i=1..32
Number of Hybrid ARQ processes
-
3
Maximum number of Hybrid ARQ transmissions
-
4
Redundancy and constellation version coding sequence**
-
{0,0,0,0}
s=1, R=0, b=0
dB
-15,05
dB
0
Ioc
dBm/7,68MHz
-60
Note *: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Note **: This sequence implies Chase combining
Table 9.4.1.2: Performance requirements for fixed reference measurement channel requirement in multipath channels for 5,3 Mbps – Category 8 - UE (7,68 Mcps TDD Option) QPSK
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
5,2
880
2
PB3
5,5
880
3
VA30
6,2
880
4
VA120
6,2
880
Table 9.4.1.3: Test parameters for fixed reference measurement channel requirements for 5,3 Mbps – Category 8 - UE (7,68 Mcps TDD Option) 16QAM
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
HS-PDSCH Modulation
-
16QAM
Scrambling code and basic midamble code number*
-
0, 1
Number of TS
-
4
HS-PDSCH Channelization Codes*
C(k,Q)
C(i,32)
i=1..32
Number of Hybrid ARQ processes
-
3
Maximum number of Hybrid ARQ transmissions
-
4
Redundancy and constellation version coding sequence**
-
{0,0,0,0}
s=1, R=0, b=0
dB
-15,05
dB
0
Ioc
dBm/7,68MHz
-60
Note *: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Note **: This sequence implies Chase combining
Table 9.4.1.4: Performance requirements for fixed reference measurement channel requirement in multipath channels for 5,3 Mbps – Category 8 - UE (7,68 Mcps TDD Option) 16QAM
Test Number
Propagation conditions
[dB]
R (Throughput) [kbps]
1
PA3
11,1
1765
2
PB3
13,2
1765
3
VA30
13,7
1765
4
VA120
13,6
1765
The reference for this requirement is TS 25.102 [1] clauses 9.3.1.1 and 9.3.1.2.
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.